Sciencemadness Discussion Board

My lab beginnings.

charley1957 - 15-7-2017 at 11:52



DSCF2165.JPG - 237kBWhen I was 14 or so, my cousin gave me an unwanted chemistry set she got for Christmas. My grandfather finally relented to my bugging and built me this chemistry lab bench. DSCF2166.JPG - 239kB The metal plate in the front center is the lid to that chemistry set. The other piece of tin you see to the right of that is where I covered up the hole that was made for a gallon ice cream bucket which was my lab sink. DSCF2168.JPG - 248kB A closeup of what is left of the periodic table that was printed on the inside of the chemistry set lid.

DSCF2171.JPG - 238kB A few years ago I found Robert Bruce Thompson's book "Illustrated Guide to Home Chemistry Experiments." I got the chemistry bug again, bad this time. So I decided to build a proper lab. I started with the old lab bench my grandfather built for me. The first thing was to clean up the top and plug up the hole.

DSCF2176.JPG - 238kB Here's the finished top. You can also see a new plywood back on it. The old one was a couple of pieces of masonite that were badly water damaged and coming loose at the bottom.

DSCF2177.JPG - 245kB This is the fume hood at the beginning.

DSCF2182.JPG - 254kB Here you can see the storm door I used as a sash for the front of the fume hood.

DSCF2183.JPG - 248kB And here is the final fume hood, until a few days ago, when I had to make it taller because I couldn't set up my Vigreux column inside. I have more pics of that, and more of the lab coming.

Continuation of my lab beginnings

charley1957 - 15-7-2017 at 14:51



IMG_2592.JPG - 57kB See the nasty-looking joint in the body of the fume hood just above the stainless bowls? That's where I extended the fume hood up just the other day. I'll paint that soon.

IMG_2593.JPG - 39kB Look at all that room inside now! The fans are from an old server, and they lead out through the wall with a piece of 4" dryer vent, to another squirrel cage fan I salvaged from a large microwave oven. It all exhausts about 5 feet above the roof.

IMG_2595.JPG - 46kB You can see a lab frame inside the fume hood. I have another I built on the main lab bench also. My last job had lots of scrap 1/2" stainless steel tubing. I picked up a bunch of that, bought some lab frame clamps on eBay, and set about making lab frames. This picture shows a plain cast iron floor hub, 1/2" NPT. Into that is threaded a 1/2" X 1/2" pipe to tubing adapter. Then the tubing is tightened in to the adapter with the brass nut. For about $4 apiece I made four or five of these, versus almost $40 apiece for commercially-manufactured ones. All this stuff I bought at the local lumber yard.

IMG_2596.JPG - 44kB Here's another one I used to secure the end of the middle rail of my bench frame. Stainless tubing was what was available to me, but the rods can be made of anything of 1/2" diameter, even solid rod of any kind.

I have ordered more lab frame clamps from eBay to finish the frames. They've worked fine without every intersection being clamped, but I just want them to be as sturdy as I can make them. I've not seen these clamps for a while, but some came on just the other day and I snagged them.

JJay - 15-7-2017 at 15:30

Nice lab. I'm using a 4 inch vent for my fume hood as well. If you're working with toxic substances (chlorine comes to mind), you want a face velocity of at minimum 60 FPM (100 is better). That works out to a sash height of about six inches.

CharlieA - 15-7-2017 at 16:53

Great job on your lab. :) May I ask the dimensions of your fume hood?

j_sum1 - 15-7-2017 at 21:33

Saweeet!!

Nice space. Your fume hood looks similar to what I am planning for mine in terms of shape dimensions and construction. I bet you're happy with it.

charley1957 - 16-7-2017 at 06:53

Thanks all for the compliments. JJay, I've seen a thread somewhere about all the calculations that go into proper fume hood design. Just know that I didn't calculate anything. I have no idea what my airflow is. I just know that I've worked with some nasty stuff and so far I've not experienced any vapor/gas escape as far as I can tell. I do wonder about my dryer vent material, though. I thought it was aluminum foil on a steel spiral, but it seems to be a stiff plastic covered by a reflective coating of some sort. I sometimes worry about something eating through the plastic. The whole thing reminds me of Mylar.

Charlie A, the fume hood's inside dimensions are 42 in. tall, 33 wide and 23 deep. The depth was determined be the front to back width of the lab bench it was built on. The aluminum storm door determined the width, and I just lately had to add on to the height because I originally built it too short. It all got a new coat of paint because of the modification. The frame rails all had a coat of rust on them, and that all got cleaned up too. I just lately found a bunch of scrap stainless steel sheeting which I used to cover the bottom of the fume hood and all my bench and counter tops with. So much easier to keep clean than painted wood.

I will post a lab tour soon in the appropriate place in the forum.

charley1957 - 16-7-2017 at 13:58

Thanks all for the compliments. JJay, I've seen a thread somewhere about all the calculations that go into proper fume hood design. Just know that I didn't calculate anything. I have no idea what my airflow is. I just know that I've worked with some nasty stuff and so far I've not experienced any vapor/gas escape as far as I can tell. I do wonder about my dryer vent material, though. I thought it was aluminum foil on a steel spiral, but it seems to be a stiff plastic covered by a reflective coating of some sort. I sometimes worry about something eating through the plastic. The whole thing reminds me of Mylar.

Charlie A, the fume hood's inside dimensions are 42 in. tall, 33 wide and 23 deep. The depth was determined be the front to back width of the lab bench it was built on. The aluminum storm door determined the width, and I just lately had to add on to the height because I originally built it too short. It all got a new coat of paint because of the modification. The frame rails all had a coat of rust on them, and that all got cleaned up too. I just lately found a bunch of scrap stainless steel sheeting which I used to cover the bottom of the fume hood and all my bench and counter tops with. So much easier to keep clean than painted wood.

I will post a lab tour soon in the appropriate place in the forum.

nanoAmp - 29-7-2017 at 06:46

Reading this post, encouraged me to break out the old chemistry set and get my lab going.

hope to post a few pics of it soon.


[Edited on 29-7-2017 by nanoAmp]