Sciencemadness Discussion Board

Have i created dichromates ...

gruen - 13-5-2018 at 17:24

I wanted to create sulfuric acid from epsom salt. (the idea was a bit to use widely available things not that i couldnt obtain the acid directly)
I used a detergent bottle cut open on the side so its handle connected the upper and lower part. Placed on its handle that forms 2 connected containers. i then cut a piece of PP fabric (shopping bag) up and stuffed it in the handle. That forms our membrane for electrolysis.
Filled the "bottle" with water and 20g of epsom salt (whatever hydrate that was).
Then used a graphite anode and magnesium cathode (the cathode material probably is irrelevant) electrolysis was done for 1-2 days at 400mA and voltage in the 50-90V range. The handle gets quite hot and the whole needed to be placed into a container with standing water for cooling.
At the cathode a white solid forms, which should be Mg(OH)2. After drying that was 2.7g.
(in fact this was my 3rd attempt at this, my first only got 0.6g and 2nd failed totally, the first used hot glue in a glass to hold the membrane, the 2nd had a long tube filled with PP fabric between 2 glasses)
The liquid at the anode was dirty from graphite and impurities from the "pure" graphite electrode from china. The liquid was quite acidic and produced expected CO2 with Na2CO3.
Now i still had a "platinized titanium" electrode from china as well. I was quite aware that it was fake and got already refunded by the seller but due to curiosity i thought id try it anyway.
The material of the electrode was slightly magnetic and had a density around 8(+.0.5)g/cm3 i guess it is Austenitic stainless steel. I only wanted to try it until i see visible loss of material but then didnt look for several hours. And when i looked it was thinner at the part that was submerged. I belive it lost about 2g of material or so. The electrolyte was orange on the anode side and the cathode was covered in solid brown gunk, i presume iron hydroxide or some other iron compound with more Mg(OH)2 mixed in.
I then spend some time trying to find out if such setup would create (di)chromates and how to change them into something less toxic.
Testing a small amount of the orange electrolyte by adding vodka results in a smell very different from ethanol and acetic acid. I assume that is Acetaldehyde. At this point the color was still orange, several hours later it changed to pale green. The original orange electrolyte when mixed with Na2CO3 also forms a brown precipitate at about pH 3 i presume that is some iron compound. The remaining liquid is orange when acidic and yellow when basic. Which matches how (di)chromates would behave ...
Trying to boil down a small sample of the liquid (in a semi proper distillation setup to avoid any acid vapors going into the air) results in a tiny amount of clear and colorless viscous liquid with tiny amount of black precipitate remaining. Cooling it showed no noticeable additional precipitate. The viscous liquid was quite acidic. All the distilled off liquid was clear, colorless and almost pH neutral, i think one drop of acid spilled over or so. IIRC The plate temperature was 250°C. I made no attempt to distill the acid itself over.

The amount of (di)chromate in the orange liquid must be quite small but still iam quite surprised how easy it was to create this. Especially considering my knowledge and experience is at a basic level only.
Not sure anything in here is new or its all well known, but maybe its useful to someone

ninhydric1 - 13-5-2018 at 18:10

It is not necessarily dichromate; it could also be Fe3+ present in solution.

woelen - 13-5-2018 at 22:44

Add a few drops of H2O2 to the orange solution. If it contains dichromate, then you get a deep blue solution.

gruen - 15-5-2018 at 05:54

Would Fe3+ not have been removed as hydroxide in the sample that i added Na2CO3 to ?
What i did exactly IIRC was add Na2CO3 drop wise until precipitate started to form (that was at pH3) then added more and filtered the precipitate off. what remained was on the basic side and yellow and clear, adding citric acid made it orange again.

H2O2 is a really good idea, i will try to obtain some

In the meantime as the question, what it is kept nagging me, even though i actually have no time ;). i searched for something else i can do with the limited set of reagents i have. I found some old silver/potassium nitrate sticks.
I took 5ml of the orange solution (see attached image 1) and added Mg(OH)2 (which i made earlier from MgSO4) with stirring. First nothing happened then precipitation starts to form i kept adding until formation of more precipitation clearly stopped. (see attached image 2) I then waited a bit and then filtered. The solution is yellow (see attached image 3). Its pH is around 8
I added a (few?) drop(s) of silver/potassium nitrate solution. It immediately turns dark red (see attachment 4). Adding more deepened the color. A bit stirring and waiting and filtering shows red solid and crystal clear liquid (see attachment 5). After washing the filter a few times with distilled water and drying at 85°C there was 13mg of red solid.

I also tried adding the silver/potassium nitrate solution to the original orange solution, this showed no effect. adding a stick directly into the orange solution though shows also some red precipitation forming around it (see last attachment)


i1.jpg - 67kB i2.jpg - 59kB i3.jpg - 72kB i4.jpg - 69kB i5.jpg - 72kB i6.jpg - 84kB

woelen - 15-5-2018 at 06:43

Based on your data, I have the impression that your solution contains a small amount of dichromate, but only a really small amount.

Silver nitrate gives a deep red precipitate with dichromate ions of silver dichromate in strongly acidic solution and a red/brown precipitate of silver chromate in weakly acidic or neutral solution.

A much more sensitive test is the test with H2O2. You'd best make a very dilute acidic solution of appr. 0.1% H2O2 + a few 0.1%'s of HCl (or H2SO4) and to this add a few drops of your test solution. Even if the test solution only contains 0.01% or so of dichromate, then you get a clearly visible beautiful blue color of a peroxo complex, CrO(O2)2.

Sulaiman - 15-5-2018 at 07:33

Last night I read woelen's post, which stimulated me to go to the shed:
In a 10ml beaker c10mg of ammonium dichromate dissolved in 3ml H2O gave a clear orange solution.
A few drops of 10% H2O2 produced a dark black/blue/brown colour, no deep blue as described ...?
so guessing a concentration problem I dumped the solution into 100ml H2O which became dichromate yellow/orange ?
pH ? ... adding conc. H2SO4 changed the top 3/4 of the solution deep blue ! ... success.
(quick test, no stirring)
Amazingly dense deep blue from so little dichromate... a very sensitive test/indicator.
Later the solution turned light blue-green.

P.S. this is the first time I've thought of hydrogen peroxide as a reducing agent.

P.P.S. it seems that sometimes there is a lot more to see without stirring than with,
e.g. a gradient of oxidation states can be seen between areas of different concentrations of reactants.

P.P.P.S. (!) or you can do it the pretty way around, maintaining excess peroxide;
https://www.youtube.com/watch?v=59nKbHbdQ-A

[Edited on 15-5-2018 by Sulaiman]

woelen - 16-5-2018 at 23:41

To make the test even more sensitive is to take 10 ml or so of your liquid to be tested, to this add a small amount of H2O2 and acid (only very small amounts should be used) and then add 1 to 2 ml of diethyl ether and shake well for a while. The ether and aqueous layers will separate again when you stop shaking. This causes the blue compound to be extracted into the ether layer, it dissolves better in ether than in water. In the ether layer it is much more stable than in the water layer and because of the smaller volume of ether you make its concentration larger.

You can even further stabilize the blue compound when you add pyridine to the solution. The compound then reacts with the pyridine, giving a bright blue/indigo compound, which separates from the solution as a solid. It is nice to try that one if you have pyridine. With that you can use higher concentrations and you can isolate the blue pyridine/CrO5 complex. i would not store the complex for a long time though, even the pyridine complex is not 100% stable and it slowly decomposes, giving oxygen and hence pressurizing the container in which it is stored if this is sealed.

gruen - 11-6-2018 at 15:21

Took me a bit long, but i finally found the time to test with H2O2. I used some 0.3% H2O2 (diluted from 3%, contains some NaCl impurity but that was easy to obtain).
Adding drops of that produces beautiful blue "clouds".
A video showing it should be here:
https://rumble.com/v5md3f-testing-for-dichromate-with-h2o2.h...

I have no pyridine nor ether. And it seemed to work fine without acidifying the H2O2, the orange solution is already quite acidic.