Mateo_swe
National Hazard
Posts: 505
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Using a 24/40 flask with my other 24/29 glassware
So i recieved my latest glassware order from ebay.
One flask, a dual neck 2000ml rbf has the wrong connections.
All my glassware is 24/29 and this flasks necks are 24/40.
Is this 24/40 flask still usable with my other glassware?
If i have understood this correctly both the 24/29 and the 24/40 has a 24mm diameter hole in the top and same taper degrees.
The only thing different is the length of the ground areas, 29mm for the European 24/29 and 40mm for the US 24/40.
So then my other 24/29 items should fit in this 24/40 flask, right?
Or are there other things that one must take into considerations here?
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
Yep, as long as the first number matches you are good, 24/29 is 29mm long so just won't protrude in as far as the 24/40, and vice-versa, the 24/40 is
40mm long so will protrude a little further ~11mm into a 24/29 ground glass joint, but both are interchangeable. I had the same fear when I got a
24/29 EM flask and all my glassware was 24/40.
Edit:
Though 1 good point to make is if you get a male 24/40 joint and using it on a 24/29 female joint, be careful with grease, you don't want the bottom
~11mm greased to prevent contamination from your grease of choice in the reaction/collection flask.
[Edited on 17-7-2020 by Syn the Sizer]
[Edited on 17-7-2020 by Syn the Sizer]
|
|
|
Mateo_swe
National Hazard
Posts: 505
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Thanks.
I can use this 24/40 flask then.
Its a nice flask and its a hazzle returning it.
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
For sure, it opens up to more glassware if the part in one joint size is sold out, you can check the other.
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
I just had a thought, I think if a person was looking for a step down adapter to a smaller joint size and you own a mixture of 24/29 and 24/40
glassware, you might want to get a 24/40, depending on the clearance at the bottom of the adapter you might not have space for the extra ~11mm to
protrude out the bottom on 24/29->19/22 adapter. I don't think it would be an issue stepping up to say 24/29->34/45
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I feared at first I ordered wrong types of joints because I just a while ago ordered glassware that is mixed with 24/29 and 24/40 joints. Luckily they
are interchangeable.
Most adapters look that they have a bulge to allow for headspace.
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
Awesome, that is good to know. I thought after I made my first reply "I wonder what the clearance on an adapter was" so thought I should mention that,
but now that I see the adapter, do remember seeing they usually have that bulge.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I personally prefer 24/29 flasks and 24/40 everything else. I have a combination of both sizes of both flasks and adapters. I have one
straight-through 24/29 adapter with a gas takeoff that that won't accept 24/40 adapters with large drip tips, but in general, it's not a problem.
24/40 joints hold together more tightly. I think that attribute is desirable for most pieces of jointware and undesireable for flasks, but the
practice of deliberately mixing 24/40 and 24/29 is not common.
[Edited on 19-7-2020 by JJay]
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
JJay, That was my original concern with adapters. I had a feeling some 24/29 adapters night have just enough clearance for a 24/29 and the extra 11mm
of a 24/40 would be too long.
I like your logic in concerns to the joint size of flasks and everything else. I agree, you want your parts to hold well and your flask to be more
easily removed. if you need to switch it out or want to pipette a sample you don't want to fight just to get the flask off.
|
|
|
Sulaiman
International Hazard
Posts: 3558
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
not a massive concern but a 24/29 joint is 21.1mm minimum diameter,
a 24/40 joint is 20mm diameter,
not a huge difference but for cleaning, poking, stirrers, the extra 1.1 mm can make a difference,
just another minor reason to favour 24/29 for flasks, or vessels.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Syn the Sizer
National Hazard
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
That is interesting to here and a very good point. I guess the 24 really only applies to the maximum diameter, and as the 24/40 drops the extra 11mm
it would still taper, 11mm makes a 1.1mm difference, would that be a 10% (9o) angle?
[Edited on 19-7-2020 by Syn the Sizer]
[Edited on 19-7-2020 by Syn the Sizer]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
