Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
How large amounts are separated?
How labs do bigger batches of separation and extraction? Bigger than 5L separatory funnels begin to get too heavy to handle, so I suppose they use
stationary, stirred separatory funnels like in brewing?
Years ago, I did an improvised separatory funnel from transparent bucket and a valve. It did work great, and cost about 5€ with all the parts.
|
|
|
itsallgoodjames
Hazard to Others
Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline
|
|
If you're trying to separate large amounts of liquids, decant as much of the liquid as possible then use a sep funnel on the rest of it
Nuclear physics is neat. It's a shame it's so regulated...
Now that I think about it, that's probably a good thing. Still annoying though.
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
During benzaldehyde synthesis I used glass tube and tubing to suction out the BzH settled to the bottom. So yeah, there are other methods too.
|
|
|
zed
International Hazard
Posts: 2277
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Use vacuum to siphon.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
I think once U go past the 5L point U go with buckets/tubs/the/drums with taps on them or go with the vacuum siphon method
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
Here is a 50L example. Coarse extraction is achieved using a bottom tap (in progress, see image). Once the boundary gets close to the drain, the flow
is slowed to prevent a vortex which would cause waste.
When the level is as close to the layer as one can best manage, the valve is closed. Rapid stirring commences to dislodge adhering liquid from the
reactor walls, followed by more settling time to let it fall to the bottom.
The bucket is meanwhile swapped for a pitcher-like transfer container eventually used to fill a 2L sep funnel. The tap is pulsed open and shut a few
times until the amount drawn reaches about 3/4 the volume of the sep funnel. This purges remnants of the heavy layer from the reactor and purges the
valve body with product. The sep funnel is used as normal for fine separation and any product is returned to the reactor for the next step.
Siphoning with a long glass tube is also an option. This method would be preferable if the next step could not tolerate any waste from the previous
step, as there are invariably adhering droplets. In my case they are taken care of during the drying step and are of little consequence.
|
|
|
njl
National Hazard
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
What solvents are you using here?
Reflux condenser?? I barely know her!
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
Just water. The bottom layer is mostly aqueous sodium sulfate with some sulfuric acid; the top is product. This is just a big acid-catalyzed
esterification.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
