Fantasma4500
International Hazard
Posts: 1677
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
The crudest anti bumping + increase heating efficiency
so ive always been a fan of tall beakers, and they oftenly do bump a lot when boiling something
ive used aluminium foil for many things, especially insulating distillation equipment and even pressed a foot for round bottom flasks, turns out it
helps massively with transferring hotplate heat as you can just make it as wide as the hotplate and you lose very little heat and you can have it
climb really far up the bottle itself
thinking back, i dont remember any bumping when distilling using my aluminium disc?
anyhow so i had to boil 100mL water in a tall 250mL beaker and i just took a piece of aluminium foil, folded in half, wrapped around beaker and
pressed down along the beaker to the bottom as pictured
https://gyazo.com/578e70d3a3e2258e2c8969ab19597661
i came back to see the whole deal bubbling and boiling vigorously, but zero bumping? none at all
and you cant even argue the aluminium foil absorbs the bumping because its in direct contact with the hotplate
as for making a round bottom flask disc you wanna take maybe equal to 6 A4 sheets of foil, fold it like 6 sheets of A4, crumble it a bit, then crush
it down to the size of a dish, put the round bottom flask on top, press it down into it a bit andthen press inwards towards the round bottom flask,
once aluminium foil is well compressed it doesnt shield from heat, it rather acts as a conductor, the disc i have made originally for 500mL flask
works well even for 50mL flask and ive had the same disc for 3 years
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
It is probably slowing the heating just enough to get good convection and if it is up the sides it is helping heat the sides which improves convection
as well. More even slower heating reduces bumping.
|
|
|
Fantasma4500
International Hazard
Posts: 1677
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
no it doesnt slow the heating but i believe what happens is that it ensures the sides of the beaker stays warm so that the solution is heated from all
sides rather than just the bottom, causing some odd physical phenomena when the bubbles interacts with a colder upper layer, or maybe the bubbling
happening on all sides of the beaker stabilizes the bubbling
but it certainly doesnt halt the heating process, it directs the heat into the beaker rather
|
|
|
Colleen Ortiz
Harmless
Posts: 19
Registered: 16-12-2021
Member Is Offline
|
|
Re:The crudest anti bumping + increase heating efficiency
When boiling water, aluminum appears to be an excellent anti-bumping agent; it makes the water boil hard and minimizes its bumping. When the water was
boiled without any aluminum foil, it bumped before boiling, wasting almost half of the beaker filled with it. The results improved significantly with
aluminum, removing virtually all the bumping. It might be due to the effect of aluminum that it allows the appropriate heating to the water and
eliminates the bumping enabling the water to boil without any bumping, allowing good convection of the heat to the water. It could also be that the
foil keeps all the sides of the beaker warm, allowing equal heat transfer to the water from all sides, making the water boil without any bumping, thus
working as an anti-bumping agent during water boil minimizing the wastage.
Bumping occurs when the upper colder layer comes in contact with the hot water bubbles, bumping starts; what aluminum does here is allow the equal
heat transfer to all areas of the water and minimizes the bumping effect.
|
|
|
Rainwater
National Hazard
Posts: 800
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
I think its more of the difference in densty than temp, but i am nit picking at this. Even heating is still the best way to work a solution. Thanks
for the tip. Ill be giving this a try
"You can't do that" - challenge accepted
|
|
|
Fantasma4500
International Hazard
Posts: 1677
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
i ran into bumping due to Na2SO4 formation- usually bumping isnt a problem as i always wrap my flasks in aluminium
adding about 20 pieces of silica gel balls completely solved it
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
