j_sum1
Administrator
Posts: 5741
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Lab refurbishment is coming along.
|
|
Bitumenous Membrane – comercial product with unusual properties
This is mostly a question to satisfy my curiosity.
I am working with a product that is used to apply a waterproof coating to concrete / cinder-block / brick surfaces that are below ground level. (I am
using it for its intended purpose. I need to prevent ground water from seeping into a basement. Digging the trench was a PITA.)
This product is a thick tarry paste with approximately the consistency of toothpaste. For use it needs to be diluted 1:1 with water and applied with
a brush.
To my surprise, it blends really well with water. It forms a grey, greasy-looking mixture that is very fluid and applies easily like decking oil.
Brushes, containers and hands wash off easily with water.
However, when the product is dried, the material is a thick and tacky tar substance with a consistency exactly the same as road bitumen. This has no
affinity with water whatsoever. It will not wash off with hot water and detergent. Ethanol has no effect on it. But it is fully soluble in
gasoline.
It dries really rapidly -- at a faster rate than expected to evaporate 50% added water. I am not sure how much water is present in the tarry residue.
Anyway, my question. What is the composition likely to be for it to have such variant properties with respect to its affinity to water?
(I guess I could ask the same question of acrylic paint, but this product's tarry-ness takes it to a whole new level.)
|
|
|
Twospoons
International Hazard
Posts: 1191
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Many years ago I used a product called "Mulseal" to seal cables into slots in tarmac. It was a bitumen - latex emulsion. Horrible stuff once dried -
rubbery tar, exactly as you'd expect. But water washable when still wet. We used it undiluted, as we were basically backfilling the cable slots and
wanted minimum shrinkage.
I imagine yours is something similar.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
Tsjerk
International Hazard
Posts: 2829
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Could you mix a weighed amount with water and weigh again after drying? It would be interesting to see whether there still is water afterwards.
|
|
|
j_sum1
Administrator
Posts: 5741
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Lab refurbishment is coming along.
|
|
Quote: Originally posted by Tsjerk  | | Could you mix a weighed amount with water and weigh again after drying? It would be interesting to see whether there still is water afterwards.
|
That's a good idea. I may do that.
I will rake some pics and report back when I do.
[Edit adding pix]
Product
Product in use
[Edited on 17-7-2022 by j_sum1]
|
|
|
Antiswat
International Hazard
Posts: 1621
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
irking feeling that there may be some silicone in it? is there solvents in it? i tried getting the MSDS but they wont give that out, i found some
vague stuff saying theres no harmful chemicals in it (just like toothpaste)
would be cool if it could tolerate +100*C and all strong acids.... very cool indeed.
|
|
|
arkoma
Redneck Overlord
Posts: 1601
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Online
Mood: ¡socialista!
|
|
I can't find the exact same product now, but we used to use something similar to this:
https://www.homedepot.com/p/Henry-0-90-Gal-107-Asphalt-Emuls...
to seal up potable water tanks in the Mojave Desert. It was a brown mixture about the texture of yogurt and water soluble until it DRIED. Then it was
black and water proof, with no volatile petroleum products.
Travel is fatal to prejudice, bigotry, and narrow-mindedness, and many of our people need it sorely on these accounts.
|
|
|
dome13
Harmless
Posts: 21
Registered: 29-6-2019
Location: Hungary
Member Is Online
|
|
I work in an asphalt laboratory and we have a bitumen emulsion plant. My daily routine is to analyze an emulsion sample. We produce "cation active"
emulsion, which means it contains hydrochloric acid in water phase. The emulsion's pH is usually 2,0-2,3. It contains water in 40% and 60% bitumen. It
has a chocholate brown colour and a characteristic odour - for me, it's like somekind of organosulfur compound.
|
|
|
j_sum1
Administrator
Posts: 5741
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Lab refurbishment is coming along.
|
|
I hope to get into the lab this weekend. I will do some tests (which will probably take a bit of time). I will add pH measurement to the tests.
It really sounds like I won't get to the bottom of it all though. It seems we have an emulsion with an affinity for water -- which is what it says on
the box. Exactly how that emulsion works looks like it is a matter for research rather than experiment. Still, it seemed to me to be a rather
interesting product with quite strange properties.
FTR, the concrete wall is now fully sealed with several thick coats. It has dried to make an impermeable membrane. Drainage pipe is now in the
trench and it is back-filled with gravel. Job done. (Not sure if the tree I was digging around will survive. I had to cut away a lot of roots.)
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
