Rainwater
National Hazard
Posts: 799
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
Preventing Pipette cross contamination
Is there a ready made solution to keep a pipette with its reagent?
Something attached to the bottle or beaker, like a cool way to tye a ruberband or something simple.
Long story:
Ive wasted a few hours this morning purifying nitric acid from a chloride contamination that turned out to be from a pipette that was used with NaCl.
Normally I wouldnt care but this batch is being used to measure silver content in scrap. So I dumped in a bunch of silver nitrate, filtered,
distilled. Then tested again. Same contamination. Switched to freshly cleaned everything and finally got the result i was looking for.
[Edited on 27-5-2023 by Rainwater]
"You can't do that" - challenge accepted
|
|
|
Parakeet
Hazard to Self
Posts: 66
Registered: 22-12-2022
Location: Japan
Member Is Offline
Mood: V (V)
|
|
You can probably use something like this.
https://a.co/d/fTs7AOO
I'm not sure if these can withstand nitric acid vapour though.
|
|
|
unionised
International Hazard
Posts: 5102
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
The traditional approach is to fix a test tube to the side of the reagent bottle with electrical tape and keep a pipette in that
|
|
|
Rainwater
National Hazard
Posts: 799
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
You sir are a genius, thank you
"You can't do that" - challenge accepted
|
|
|
Sulaiman
International Hazard
Posts: 3558
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I'm a little wasteful in this respect
- I buy disposable pipettes in bags of 100 pieces.
Edit: I reuse pipettes during an experiment but at cleanup time I dispose of most of them.
For an occasional chemist like me, dust/moisture/CO2 etc. accumulate between experiments.
Plus, many of the liquids used are volatile and corrosive,
I prefer to seal all of my liquids from the atmosphere between experiments.
And one mistake can ruin an entire bottle of stuff.
I can easily imagine environments where usage is so frequent that reuse , or automatic dispensers, are common.
[Edited on 28-5-2023 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
B(a)P
International Hazard
Posts: 1114
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
You can buy yourself some dropper bottles and decant an amount of your frequently used reagent into that. You obviously need to check for
compatibility between your reagent and the material that the bulb is made from.
Personally I do the same as Sulaiman. It feels wasteful sometimes, though to me the benefits outweigh the additional consumables.
|
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
The bulbs from dropper bottles generally dont withstand sh**.
- Deschem's just rot away with time in their box. One bottle had stannous chloride in it and was in the kitchen (sun, heat, grease) it left a red
sticky goo between my fingers when I tried to use it.
- Better quality from a lab supplier will last just a bit longer.
Dont store anything volatile or corrosive in them.
I slapped myself in the face when reading Unionised great suggestion. Genius indeed !
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
