Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Delaney concrete-body lathe
watson.fawkes
International Hazard
*****




Posts: 2793
Registered: 16-8-2008
Member Is Offline

Mood: No Mood

[*] posted on 13-4-2012 at 07:01
Delaney concrete-body lathe


Pat Delaney has designed a lathe that's designed to be reasonably accurate and dirt cheap, because its body is made of concrete. The lathe bed is concrete, the headstock is concrete, the cross-slide bed is concrete, and the tailstock is concrete. Those pieces are typically made from cast iron. The precision elements are metal, as usual: the ways, the bearings, the screws. The real advantage is getting rid of the need to deal with the structural cast iron pieces.

If this sounds absurd, Pat Delaney is the creator of the multimachine, a shop-built machine tool based around a discarded engine block. The brilliance of that design is that the cylinder bores need to be exactly parallel in order to work, so he indexes the accuracy off a pair of those bores. Now for this project, he's in failing health and won't be able to build his own prototypes. Nevertheless, they're worth taking a look at. Delaney is a spiritual successor to David Gingery, although he didn't write as much as Gingery did.

Resources: original project site (on wikispaces), the new project (on Make: Projects, where you can download a complete PDF), the Multimachine group (on Yahoo! Groups).

So why is this significant? Fabrication is a limiting factor in lots of interesting experimentation. This is a much lower cost entry to machining than has previously existed. It's sweat equity, to be sure, but it's still equity in the end and is available to those without the monetary resources to do machining.

Personally, I've been scheming about building a glass lathe, because they're even more prohibitively expensive new and they're almost nonexistent used. This basic construction technique eliminates the main hurdle I was facing, which is that I didn't have a cupola to do the cast iron.
View user's profile View All Posts By User
Magpie
lab constructor
*****




Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline

Mood: Chemistry: the subtle science.

[*] posted on 13-4-2012 at 08:36


Quote: Originally posted by watson.fawkes  

Fabrication is a limiting factor in lots of interesting experimentation.


I would agree with this based on my own experience. Eg, neither I nor garage chemist have been able to fabricate a ceramic (in my case mullite) tube with a male end that will seal satisfactorily to a standard taper female glass fitting. I'm still working on this, however.

Many times I have wished that I had a proper metal working shop complete with lathe and welding equipment, and that I knew how to use said equipment.




The single most important condition for a successful synthesis is good mixing - Nicodem
View user's profile View All Posts By User
bquirky
National Hazard
****




Posts: 316
Registered: 22-10-2008
Location: Perth Western Australia
Member Is Offline

Mood: No Mood

[*] posted on 13-4-2012 at 09:12


Its a good idea and i don't wont discourage anyone that wants to give it a go to prove it can be done. or to build it as a project in its own right.


however Ill offer my own experiences and thoughts.

I built my own CNC milling machine out of random odds and ends the most expensive part was the cross slide that i decided to buy off the shelf that was about $200 au I started with the chassie of a old drill press but there is almost none of that left now.

I had to spend a LOT of time getting the structure setup Just so in order to reduce vibration and get reasonable performance Lots of messing with motors and bearings more broken end mills than i can count. I had a fire caused by a slipping belt an alarmed neighbor and subjected my missus hours days and weeks of loud chattering that surely cost me some relationship capital ;)


But i got there in the end. and im quite proud of my Frankenstein contraption

but to be brutally honest
if i had spent 1/100th that time making my own lunch to take to work I could have saved enough money to buy a cheap Chinese mill and do a cnc conversion over a weekend

Unless you need to machine physicly large items. (like say a cannon!) i think you will be better off putting up with a cheap import and spending your time working on what your actually trying to build
View user's profile View All Posts By User

  Go To Top