Number 9
Harmless
Posts: 34
Registered: 23-3-2012
Location: Grajagan
Member Is Offline
Mood: ingin tahu semua
|
|
Help! I lost my stir bar for tomorrow
I have a project to do but I lost my stir bar.
I can use iron, which is magnetic and this really works on a magnetic stirrer.
The point is that I must use it to stirr mixed acid (conc. sulfuric acid and 68% HNO3). So, I suppose that this simply dissolve in this mixture.
What can I do to protect my iron magnet. Is a silicon layer a good option?
For industrial magnets they use teflon, but as a result of the high melting point, I think it's weird to use.
Any troubleshooters who can help me?
Thanks in advance!
|
|
|
Lambda-Eyde
National Hazard
Posts: 857
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Postpone the project, order a new stirbar. Buy more than one so you won't have to delay syntheses for such banal reasons anymore...
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
dann2
International Hazard
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Wrap a bar magnet (or piece if Iron of your stuck enough) in plumbers teflon tape. I believe it works.
|
|
|
ScienceSquirrel
International Hazard
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination! 
|
|
Your best option could be to seal a small bar magnet in a thick glass tube.
They used to be available commercially and I used to use them for difficult reactions that would attack teflon.
They worked well as long as they spun rfegularly at low speeds, if they broke free they could be disastrous as they might bounce off the sides of the
flask and shatter.
|
|
|
cyanureeves
National Hazard
Posts: 737
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
get a piece of nail or screw and push it into an empty plastic bic pen and melt both ends shut.
|
|
|
Sedit
International Hazard
Posts: 1939
Registered: 23-11-2008
Member Is Offline
Mood: Manic Expressive
|
|
Coat a bar magnet in Epoxy, I have done this many times.
Teflon tape will unravel do not try it.
Knowledge is useless to useless people...
"I see a lot of patterns in our behavior as a nation that parallel a lot of other historical processes. The fall of Rome, the fall of Germany — the
fall of the ruling country, the people who think they can do whatever they want without anybody else's consent. I've seen this story
before."~Maynard James Keenan
|
|
|
kavu
Hazard to Others
Posts: 207
Registered: 11-9-2011
Location: Scandinavia
Member Is Offline
Mood: To understand is to synthesize
|
|
Non-chemically inert plastics are not a good idea as Number 9 stated to be using it for a nitration mixture. For such reactions a good commercial
stirbar would be more or less the only way to go. Another method would be to use an overhead stirrer with a glass/teflon stirhead.
[Edited on 20-6-2012 by kavu]
|
|
|
Number 9
Harmless
Posts: 34
Registered: 23-3-2012
Location: Grajagan
Member Is Offline
Mood: ingin tahu semua
|
|
I agree with kavu. It is scientific proven that an empty plastic pen filled with iron and coated with epoxy doesn't work for nitration of
chlorobenzene to 4-nitrochlorobenzene. The black stirrer bar was 'gonnna with the wind' after less then one hour. Madscience!
 
[Edited on 20-6-2012 by Number 9]
|
|
|
kavu
Hazard to Others
Posts: 207
Registered: 11-9-2011
Location: Scandinavia
Member Is Offline
Mood: To understand is to synthesize
|
|
There's a great safety risk involved when unknown mixtures of organic material are allowed to nitrate. The reaction might have gone out of control and
now you have a gunky mixture of all sorts of nasty nitrated stuff, ouch :/
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
