metalresearcher
National Hazard
Posts: 731
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
Make SO3 by oxidizing SO2 with KClO3?
Well, I thought about a setup with burning sulfur and leading the resulting SO2 over (molten) KClO3 and making use of its strong oxidizing properties
especially at elevated temperatures. My hope is obtaining SO3 which can be combined with water
to H2SO4.
Does this work ?
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
I had luck just melting S and mixing in enough potassium nitrate to keep it burning good. The reulting "pucks" burned slowly and controlled in a semi
sealed vessle, and the fumes absorbed into water to give dilute sulfuric acid... Surface contact of the gas to the moltent salt may be a issue.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
Marvin
National Hazard
Posts: 995
Registered: 13-10-2002
Member Is Offline
Mood: No Mood
|
|
metalresearcher, I can think of at least 4 reasons that is a bad plan. Think about the chemistry and see how many you can guess. You need to review
basic safety information regarding chlorates.
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
Buy some platinized asbestos...
I never asked for this.
|
|
|
bfesser
|
Thread Moved
18-12-2013 at 05:08 |
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Try the lead chamber process, it worked well for me.
KNO3 is much cheaper than KClO3 and it is known to work, unlike your plan, also the setup for the lead chamber process is much more simple.
|
|
|
Random
International Hazard
Posts: 1018
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
Isn't this going to be armstrongs mixture if something goes wrong?
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
Metal researcher, I have a procedure for the lead chamber process in my lab scale industrial process, available in the pre-pub sub forum. Or you could
try the contact process, worked really well for me.
I never asked for this.
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
OK, for those interested in a simple inexpensive route to SO3, may I suggest the thermal decomposition of Aluminum sulfate. Source, see www.researchgate.net/publication/225909780_Thermal_decomposi... . Cited reaction occurring at 770 C per Wikipedia:
Al2(SO4)3 (s) =Heat=) Al2O3 (s) + 3 SO3 (g)
I am investigating some simple paths for the home chemists to prepare Aluminum sulfate. For example, dissolving Al in aqueous NaHSO4.
[Edited on 18-12-2013 by AJKOER]
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
Or buying a Kg of alum for 7$ at the hardware store, it is used for pools. Bisulphate work better anyway...
I never asked for this.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
I have used the thermal decomposition of aluminum sulfate, it works fine, except it's a pretty high temp.
|
|
|
DubaiAmateurRocketry
National Hazard
Posts: 841
Registered: 10-5-2013
Location: LA, CA, USA
Member Is Offline
Mood: In research
|
|
Heating copper sulfate to 600+ degree give SO3, or if you can get sodium persulfate, great, it works same way but with less temperature.
Heres a paper published by our lovely members on H2SO4 synthesis from SO3
http://www.sciencemadness.org/member_publications/SO3_and_ol...
Read it, and perform it nicely/carefully, SO3 and H2SO4 are extremely corrosive and you should take as much precautious and read more about it before
you do it.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Except, I don't have (98-99%) conc. sulfuric acid to react with the oleum.
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
If you can find sulphur, making sulphuric acid is not really hard, especially if you can find platinized asbestos. If you can find nitric acid too. It
is best to have an ounce of starting sulphuric acid, it is easier to make more with some.
P.S: If there is interest I could manage to make some platinized asbestos. Got "enough" asbestos, and a gram of Pt on hand.
Just found that:
http://www.ebay.ca/itm/Platinum-catalyst-5-Pt-metal-content-...
[Edited on 19-12-2013 by plante1999]
[Edited on 19-12-2013 by plante1999]
I never asked for this.
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Yes, Al2(SO3)3 is a relatively high temperature path to SO3.
However, I am investigating the possibility of a lower temperature preparation for SO3. First, I cite Atomistry.com on properties of Nitrous acid (see
nitrogen.atomistry.com/nitrous_acid.html ):
“On the other hand, many reducing agents are oxidised, the primary decomposition being: 2HNO2 = 2NO + O + H2O. Stannous chloride is converted into
stannic chloride, sulphuretted hydrogen into sulphur, sulphur dioxide into sulphur trioxide.”
Also, per the same source, some important comments:
“The decomposition of a cold dilute solution [of Nitrous acid] follows the reaction 3HNO2 ⇔ HNO3 + 2NO+H2O, whereas stronger solutions at
higher temperatures decompose according to the equations 2HNO2 ⇔ N2O3 + H2O ⇔ NO + NO2 + H2O. Other factors also influence the
decomposition, such as agitation, surface area, and presence of nitric acid. “
There is also another 2004 published source, "Nitrosation Reactions and the Chemistry of Nitric Oxide", by D.L.H. Williams, mostly accessible online
as a Google book at http://books.google.com/books?id=BVv0Lytq8foC&pg=PA14&am... per Equation [10] and [11] on page 3 and Equation [35] on page 16, I surmise the
possibility of the following under the appropriate reaction conditions/medium:
2 HNO2 + H2SO3 --> 2 NO + SO3 + 2 H2O
Or, removing one water:
2 HNO2 + SO2 --> 2 NO + SO3 + H2O
which is in agreement with Atomistry’s “2HNO2 = 2NO + O + H2O” acting on SO2 to reputedly form SO3.
Also, as 2 HNO2 = H2O + N2O3, assuming a nearly or totally non-aqueous condition, the implied reaction would be:
N2O3 + SO2 --> 2 NO + SO3
Interestingly, I am not alone in this last speculative delineation as to quote, albeit an old reference, from the “The Manufacture of Sulphuric Acid
and Alkali, with the ...”, Volume 1, Issue 2, page 1021 by George Lunge (link: http://books.google.com/books?pg=PA1021&lpg=PA1021&d... ) ):
“(2) In the atmosphere of the lead chambers it takes three seconds to oxidise NO to N2O3, or four minutes to carry on the oxidation as far,as NO2.
Since it is unlikely that in the lead chambers molecules of N2O3 and SO2 meet so rarely that the former have time to oxidise into NO2, it is necessary
to assume that N2O3 is that oxide of nitrogen which reacts with SO2 in the lead chamber. “
Here is another source (also dated) on the Lead Chamber process to quote from "The School Chemistry: A New Text-book for High Schools and Academies",
by Elroy McKendree Avery, page 341 at http://books.google.com/books?pg=PA341&lpg=PA341&dq=... .To quote:
"Although we have no reason to think that some of the reactions in the manufacture of H2SO4 are not simultaneous, we may, with propriety, trace them
as if they were really consecutive. Several such explanatory series of reactions have been written out. One of these is herewith given, not as a
didactic statement of what actually takes place, but as a theoretical exposition of what may take place.
(1) 4 FeS2 + 11 O2 = 8 SO2 + 2 Fe2Os, or S + O2 = SO2.
(2) 2 HNO3 + 2 SO2 + H2O = 2H2SO4 + N2O3.
(3) SO2 + N2O3 = SO3 + 2 NO.
(4) SO3 + H2O = H2SO4.
(5) 2NO + O2 = 2NO2, or 4NO + O2 = 2N2O3.
The NO2 and the N2O3 formed by these reactions are absorbed by the concentrated H2SO4 in the Gay-Lussac tower, combining chemically to form
nitrosyl-sulphuric acid.
2 H2SO4 + N2O3 = 2H(NO)SO4 + H2O.
This nitrosyl-sulphuric acid is pumped back to the Glover tower, where it comes into contact with steam, whereby H2SO4 and N2O3 are formed.
2H(NO)SO4 + H2O = 2H2SO4 + N2O3".
So, an alternate synthesis of SO3 may be possible working with SO2 and HNO2 or N2O3 (or, more correctly, with the mix gaseous form NO + NO2) directly.
In essence, this is a refined Lead Chamber process using efficient reactions to generate NO and NO2 (like with the respective reaction of Copper with
dilute and concentrated Nitric acid) and react with SO2.
[Edited on 19-12-2013 by AJKOER]
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Plante1999, yes I have a lot of sulfur, Can't afford (even a gram) of Pt.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Plante1999, You got the Contact Process to Work???
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
I got it to work, but I did not repertoriate it online. The catalyst in the ebay link is perfect for that purpose, although you need fairly pure
sulphur/sulphur dioxide if you don't want to poison the catalyst. You will need some time to build a suitable reactor. Rubber and latex can be present
up to the catalyst, after which glass and metal only is recommended.
I never asked for this.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
What kind of metal? I guess stainless steel could work, right.
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
Stainless is very good, even bare steel can be used if you don't mind a small amount of iron in your product.
I never asked for this.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Really???, I've always thought that ''bare steel" would corrode in the presence of Hot SO3, anyways, how about galvanized steel.
|
|
|
cpman
Harmless
Posts: 36
Registered: 9-12-2013
Location: Austin, TX
Member Is Offline
Mood: No Mood
|
|
Galvanization would have little effect. Galvanized steel corrodes less in ambient conditions is the galvanic effect, where the plating prevents the
iron from corroding by corroding first. It would not hold up that much longer than normal steel.
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Of coarse I could clean the Zn off, with HCl, or something.
|
|
|
cpman
Harmless
Posts: 36
Registered: 9-12-2013
Location: Austin, TX
Member Is Offline
Mood: No Mood
|
|
But then it would be no better than bare steel...
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
Of coarse, but the Zn might cause problems, and it does not offer much protection as it will be consumed, and turn into ZnSO4.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
