zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
What is this device?
My mother-in-law found this device I believe at an estate sale. I have spent several hours researching it to no avail. The end unscrews and seems to
have an electrical connector. I apologize for the photos. I tried to shrink them best I could with PS Express.
Edit: thought I would mention that the top of the wand is wood and very light weight.
  
[Edited on 2-10-2014 by zenosx]
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
Probably a standardized electromagnetic radiation source based on the V/r and the fact that Baldwin Instrument Co filed British Patent 689,857.
The less you bet, the more you lose when you win.
|
|
|
phlogiston
International Hazard
Posts: 1376
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
My guess is a Farmer Ionization Chamber (aka Farmer-Baldwin ionization chamber)
Internally, it contains a conducting rod centered along the length the chamber, which is connected to the
central small round metal pad at the end you are holding in the 2nd photograph. The outside is electrically connected to the outer casing of the
chamber.
When connected to an electroscope, ionizing radiation passing through the chamber will discharge the electroscope at a rate proportional to the
radiation level.
The electroscope serves both to apply the necessary high voltage and provide a readout.
Ask mum if there were any devices at the estate sale that might resemble a radiation source... lost Ra needle perhaps?
And tell here to carry a dosimeter next time.
[Edited on 2-10-2014 by phlogiston]
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
I havent yet hit it with the gieger counter but think I will do so.  . I did find
some info that it was used for dosage rates on persons after the nuclear weapons in Japan, notably dental exposures but was unable to access the full
artical. But I also found things about reverb measurements for nuclear weapon video taping. So basically it's probably a type of gieger'ish probe for
radiation measuring?
If anyone has more info that's great but with the V/r I was also going with maybe a calibration probe for some type of ionizing radiation. The high
voltage looking connector at the back also lead to that conclusion, however the light wood threw me. Perhaps it's more transparent to gamma/ect.
Ionizing radiation?
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
Thanks bbartlog! Doh why didn't I search the patents!
AND
Thanks to phlogiston, you filled in the rest of my questions.. I knew someone here was smarter than myself
Thanks!
[Edited on 3-10-2014 by zenosx]
[Edited on 3-10-2014 by zenosx]
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
phlogiston
International Hazard
Posts: 1376
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
Are you sure it is wood, not bakelite or something of that kind?
The same kind of device is still in common use today for certain radiation measurements.
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
No I am quite certain it is wood and not Bakelite or it's ilk... Not only the feel but scratch tests confirm it is wood.. It seems to be a hard wood,
but I cannot discern if the striations in the cylinder are from manufacturing or from usage....
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
But yes, it is certainly made of wood, and not a light wood like balsa for instance. I am stumped but there were a lot of crazy medical devices made
at the turn of the 20th....
[Edited on 3-10-2014 by zenosx]
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
zenosx
Hazard to Others
Posts: 188
Registered: 7-7-2012
Location: East TN / Near Oak Ridge
Member Is Offline
Mood: Awaiting Results....
|
|
Possibly it is a vernier of hard wood over an instrument casing?... If interested I will take out the obviously brass screws and disassemble this
device
A question that sometimes drives me hazy: am I or are the others crazy?
Albert Einstein
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
