greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
Ethanol chlorination..
Hi. Chlorination of ethanol aiming towards chloral hydrate.
I dont know if the pic will show up, but HCl dripped onto KMN04 to generate Cl2. Gas goes thru H20 and then thru H2S04 down into 95% ethanol.
The ethanol turned syrupy but did not solidify. Not enought Cl2? It ran about 2hrs total, after about 1 hr I turned on the heat under the ethanol and
it refluxed for about a 1/2 hr, with me plugging and unplugging the power supply.
Green fog turned the water in the first gas cleaner piss yellow and when I was done I removed the hose and white fumes arose. Whats in this now?
H2S04 in the drying bottle turned it funky yellow too.
Any uses for these two substances? that Im not aware of yet?, otherwise I'll probably chuck 'em.
I suspect the ethanol needs way more chlorination. I've perused the threads, searched and planned...maybe not enough apparently.
Ideas? The syrupy ethanol is bottled up so as not to waste, for a 2nd try.
[Edited on 19-5-2005 by greenyppols]
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
another pic
Another Pic to give better idea.
|
|
|
Esplosivo
Hazard to Others
Posts: 491
Registered: 7-2-2004
Location: Mediterranean
Member Is Offline
Mood: Quantized
|
|
If it's chloral, add a sodium hydroxide solution to it and leave to settle. A bottom layer of chloroform shoudl be seen quickly enough.
Theory guides, experiment decides.
|
|
|
Marvin
National Hazard
Posts: 995
Registered: 13-10-2002
Member Is Offline
Mood: No Mood
|
|
Not from personal experience, but the method I know of is rather sensitive to moisture. If dry chlorine is bubbled into absolute alcohol until it
won't absorb anymore it is supposed to set solid forming chloral alcoholate, from which the hydrate can be prepaired. There is no refluxing
involved as far as I can tell. I'm under the impression that the more water in the mixture the lower the yeild. Was the sulphuric acid doing a
good job of drying the gas? Could you have used ethanol with less water in? If this isnt the problem then its certainly not enough chlorine. Are
you sure refluxing the mixture doesnt decompose it at all?
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
assumed failure?
Marvin - No, Im not sure about refluxing, I tried NOT to (unplugging) but I read it was ok to just add distillate back, so I thought it'd be ok
anyway.
ethanol was not absolute. dont know how dry chlorine was. Spectacular yield was not expected, low end, if anything.
the alcohol stayed clear, where the water and sulphuric turned pee yellow.
Esplosivo - Im not after chloroform.
I transfered the syrupy stuff to a flask and plugged a cork in it. Rinsed the bottle out with water.....white fumey stuff arose..would it be I only
accomplished acidifying the hell out of the ethanol and am nowhere near chlorinating it for chloral?
I realize this is just a step, Id have to purify it after, but I cant get past this step.
Im wondering if Ithe first wash bottle didnt have enuff water to absorb hydrogen chloride this was to generate also?
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
great....seems generating CL2 this way makes the hydrogen chloride that makes HCl after I run it through the water...and the hydrogen chloride that
wasnt being absorbed anymore by the water was apparently absorbed by the ethanol, after I found this
Ethanol, reacts with Hydrogen Chloride, to form Ethyl Chloride, (i.e. chloroethane) and Water.
I read this HCl water in the 1st wash bottle ends up around a concentration of 43% HCl, higher than the muriatic HCl of 31% or so? Inteeeresting....
So I must use more water next time? Or a cleaner source of CL2.
[Edited on 19-5-2005 by greenyppols]
[Edited on 19-5-2005 by greenyppols]
|
|
|
garage chemist
chemical wizard
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
For one mol of alcohol, you need at least 4 mol of chlorine (assuming that all chlorine reacts- this is almost never the case, so more is usually
required). Calculate it.
And absolute alcohol gives very low yields of chloral, a mixture of water and alcohol is usually employed. There was a thread about it here where the
optimal mixture (which directly produces chloral hydrate) was posted.
The reaction of HCl with ethanol is of no importance here, as it requires special conditions (catalyst) which are not given here.
[Edited on 19-5-2005 by garage chemist]
|
|
|
Marvin
National Hazard
Posts: 995
Registered: 13-10-2002
Member Is Offline
Mood: No Mood
|
|
The other thread is,
http://www.sciencemadness.org/talk/viewthread.php?tid=2535
A mirror of the prep on Rhodium is,
http://designer-drugs.com/pte/12.162.180.114/dcd/chemistry/c...
HCl I'm sure isnt going to cause issues with the reaction. The methods I have here (3 books) resemble closely the Smoothe method. Saturate
anhydrous ethanol with chlorine, raise to 60C and stop when no more HCl is given off. Add conc sulphuric acid, decant, treat with calcium carbonate
(or oxide, I forget, I suspect this step is to remove any trichloroacetic acid also), distill and add to water to form the hydrate.
I can't locate what I thought I'd read recently to indicate the more water the less chlorinating and the more oxidising happens. Several
methods including Smoothe's specifically call for anhydrous ethanol, though Smoothe has added a lot of suspect hacks to a method presumably from
a textbook.
Esplosivo's suggestion was to try making chloroform from a sample in order to test if what you had was fully chlorinated.
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
Marvin - Those were the posts I read and then couldnt find again, near the end where it adds HCl. (before I get hollered at, yeah I searched for it, I
didnt go far into its depths)
I read the "sani-flush" version too...uhm..it gives me ideas but those instructions leave something to be desired. lol. At least in what
order to do stuff. I had hoped to reach the 1st impure status, as I have no 90%+ h2so4 yet for the next step in it. Im not sure if the impurities in
the store-bought concentrated h2so4 plastic bagged black stuff will affect it and Im not inclined to find out. I'll get to that next when I have
a reason too, like having impure stuff. Looks like vacuum distillation would be the best/easiest way to go as far as distilling the
"blended" stuff out.
I also see I used WAYYYYYY to much ethanol..I used something like 225ml. Me bad. So I'll try again using 25ml of the stuff thats already stopped
up.
garage chemist - so if one mole ethanol is 46g and one mole cl2 is 35g...
thats alot of cl2 if I can only expect 0.412 g of Cl2 from reacting 0.367 g of KMn04 with 6.2ml of HCl (I used something like 50g KMn04) ...Im
surprised it managed to turn syrupy at all, but it must have been in the right direction, just way too much ethanol.
I didnt add HCl for water, becaue I thought I already had plenty of it. Thats what I get for thinking, I guess.
So Im thinking of taking 25ml of this and adding some HCl just to see if anything happens with what I've acquired. ha!Probably not..
|
|
|
garage chemist
chemical wizard
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
Small correction: One mol of Cl2 is 71g (it's diatomic).
And with the 4 moles I meant 4 moles of diatomic chlorine.
I will also try the production of chloral hydrate at some time, because I now have an excellent chlorination apparatus which can chlorinate the hell
out of every organic substance .
I managed to chlorinate toluene to benzyl chloride (temperature in the liquid 157°C) in about one hour (with a 500W floodlight 50cm before the
reaction vessel).
A tip: make your chlorine from TCCA and HCl, it gives you two times as much chlorine from a given amount of HCl than with KMnO4.
|
|
|
chloric1
International Hazard
Posts: 1070
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
Nice bubblers
| Quote: | Originally posted by greenyppols
Another Pic to give better idea. |
Hey greeny, where did you get the pretty bubblers?
Fellow molecular manipulator
|
|
|
Organikum
resurrected
Posts: 2329
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: busy and in love
|
|
You should be able to do this with TCCA in situ.
|
|
|
garage chemist
chemical wizard
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
Now there's a verified synthesis procedure for chloral hydrate on www.lambdasyn.tk.
Thanks, Mephisto!
Note that if 45g of chlorine need to be absorbed, you have to bubble in 90g of chlorine because half of the Cl2 escapes as HCl. This is important when
calculating the amounts of TCCA and HCl in the gas generator.
@ Organikum: That might be possible, but separation of the chloral would be difficult.
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
chloric- sorry for the obscene delay. Dont know how I missed the ?. I was going over the threads before I attempted this again.
The bubblers came from everyone's favorite on-line auction site.
gc - what is this apparatus which you describe? Got a pic, or description? And would a 400w MH HID light work? How about a 1000w HPS? I have both in
air cooled hoods, so Im thinking the whole setup might sit right in the enclosed hood, if I stand the light on its side.
[Edited on 27-10-2005 by greenyppols]
|
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
Under some conditions, chlorine reacts with ethanol to form ethyl hypochlorite. For this reason, it may not be such a good idea to try to pass
chlorine into methyl alcohol.
| Quote: | Ethyl hypochlorite can be formed by passing chlorine into a solution of water, ethyl alcohol, a limited quantity of sodium hydroxide. Methyl
hypochlorite is a dangerously sensitive explosive.
Journal of the Chemical Society, Volume 50, p607
Ethyl hypochlorite reacts with sulfur dioxide to form ethyl chlorosulfonate, CH3-CH2-O-SO2Cl,
This could potentially be useful as a reactive alkylating agent, like dimethyl sulfate, though I am not sure if it is as hazardously toxic.
|
Here is a possible reaction mechanism for the chlorination of ethyl alcohol to chloral hydrate:
| Quote: |
CH3CH2OH + Cl2 --> CH3CH2OCl + HCl
I suspect ethyl hypochlorite is not particularly stable, and could decompose on heating, in a similar way to the tautomerisation of acetone into its
enol form.
CH3‒CH2‒O‒Cl
CH3‒CH=O Cl[-] H[+]
H[+] CH2=CH‒O[-] HCl
CH2=CH2‒OH HCl
(this tautomer of acetaldehyde would immediately become chlorinated by more chlorine, and indeed it is likewise known that acetone can be chlorinated
in the same way to chloroactetone)
Cl‒CH2‒CHCl‒OH
Cl‒CH2‒CHCl‒O[-] H[+]
Cl‒CH2‒CH=O Cl[-] H[+]
This chlorination process then repeats again two more times until the acetaldehyde is fully chlorinated on the β-carbon atom.
Cl3C‒CH=O
(at this point the chlorines are electron-withdrawing enough to make the aldehyde group acidic, and so it "hydrates" with water)
Cl3C‒CH(OH)2
|
I'm not saying let's go kill all the stupid people...I'm just saying lets remove all the warning labels and let the problem sort itself out.
|
|
|
chemcam
Hazard to Others
Posts: 423
Registered: 18-2-2013
Location: Atlantis
Member Is Offline
Mood: I will be gone until mid-september, on a work contract.
|
|
I know what I am about to say doesn't really relate to the latest post but I was wondering what would happen if you ran chlorine gas through a
condenser chilled in dry ice/acetone to get liquid chlorine and then added that to chilled ethanol would it help or hinder the chlorination?
Also, what if both the liquid chlorine and the ethanol were added together in some sort of reaction vessel that would hold the pressure of the
expanding chlorine during warm up?
Are either of those methods worth experimenting with or is it an incredibly stupid idea?
|
|
|
bfesser
Resident Wikipedian
Posts: 2114
Registered: 29-1-2008
Member Is Offline
Mood: No Mood
|
|
If your target is 2,2,2-trichloroethane-1,1-diol (<a href="http://en.wikipedia.org/wiki/Chloral_hydrate" target="_blank">chloral
hydrate</a> <img src="../scipics/_wiki.png" /> , I would think you would
have issues; it has a melting point of 57 °C, <em>well above</em> dry ice/acetone slush at -78 °C. But perhaps a
sufficient rate of reflux would wash any product (crystallized out of the refluxing solution) back into the reaction flask. <a
href="http://en.wikipedia.org/wiki/Chlorine#Physical_characteristics_of_chlorine_and_its_compounds" target="_blank">Chlorine</a> <img
src="../scipics/_wiki.png" /> will condense at -34.04 °C (1 <a href="http://en.wikipedia.org/wiki/Atmosphere_(unit)"
target="_blank">atm</a> <img src="../scipics/_wiki.png" />, and I
don't see a need to go far below that. Perhaps you could try cooling with a <a
href="http://en.wikipedia.org/wiki/Cooling_bath#Ethylene_glycol_and_ethanol_baths" target="_blank">mixture of ethylene glycol, ethanol, and dry
ice</a> <img src="../scipics/_wiki.png" /> to achieve something around -40 °C.
<img src="../scipics/_warn.png" /> Warning: I've had some bad experiences with CO<sub>2</sub>(s)/acetone—including a
carbonated <a href="http://en.wikipedia.org/wiki/Vacuum_flask#Research_and_industry" target="_blank">Dewar</a> <img
src="../scipics/_wiki.png" /> geyser in my old kitchen! That happened on one of the coldest days last (?) winter, needless to say, it was
unpleasant having to ventilate the house for several hours. 
[Edited on 7/13/13 by bfesser]
|
|
|
Texium
|
Thread Moved
20-12-2023 at 12:48 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
