Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Copper Acetate
kazaa81
Hazard to Others
***




Posts: 368
Registered: 30-4-2004
Member Is Offline

Mood: ok

mad.gif posted on 8-5-2006 at 04:51
Copper Acetate


Hi,

I have searched for copper acetate on some stores, grocery included (anything that isn't a chemical supplier), but I haven't found nothing or just CuSO4.
I've tried artistics too but they no longer sell it.

Does anyone suggest me a place to buy copper acetate? or instead another acetate, so that I will do a methasynthesis?

Thanks

Copper (I) Acetate
CuC2H3O2
CAS #: 598-54-9
Mol. 122.590 g/mol
Form: colored crystals
M.P. Decomposition
B.P. Sublimation
Sol. Reacts with H2O

Copper (II) Acetate
Cu(C2H3O2)2
CAS #: 142-71-2
Mol. 181.635 g/mol
Form: blue-green hygroscopic powder


[Edited on 8-5-2006 by kazaa81]
View user's profile View All Posts By User
The_Davster
A pnictogen
*******




Posts: 2861
Registered: 18-11-2003
Member Is Offline

Mood: .

[*] posted on 8-5-2006 at 04:55


CuSO4--(one of several methods)-->CuO
CuO+HAc--->Cu(Ac)2




View user's profile View All Posts By User
kazaa81
Hazard to Others
***




Posts: 368
Registered: 30-4-2004
Member Is Offline

Mood: ok

[*] posted on 8-5-2006 at 05:02


unfortunately my acetic acid source is just food-grade 5% vinegar...too much impurities and water...
Can you post some of the methods of conversion of CuSO4 to CuO?

Thanks rogue
View user's profile View All Posts By User
mantis
Harmless
*




Posts: 38
Registered: 17-7-2005
Member Is Offline

Mood: No Mood

[*] posted on 8-5-2006 at 06:30


Quote:

Can you post some of the methods of conversion of CuSO4 to CuO?

Add NaOH to a CuSO<sub>4</sub> solution and boil it.
View user's profile View All Posts By User
gsd
National Hazard
****




Posts: 847
Registered: 18-8-2005
Member Is Offline

Mood: No Mood

[*] posted on 8-5-2006 at 06:49


It is better and easier to convert CuSO4 to Basic Copper Carbonate. Add stoichiometric quantity of Na2CO3 solution to CuSO4 solution and wash the green precipitate of CuCO3.Cu(OH)2 with water till neutral to pH. Then decant the water as much as possible and boil with slow addition of Acetic Acid till all carbonate reacts.

CuAc2.H2O has low solubility in water at room temp. (about 5% w/w) Hence you need to filter the boiling solution to get rid of insoluble impurities.
View user's profile View All Posts By User
PainKilla
Hazard to Others
***




Posts: 306
Registered: 29-4-2004
Member Is Offline

Mood: No Mood

[*] posted on 8-5-2006 at 10:31


I used vinegar and CuO to get Cu(Ac)2 in excellent yields. You need to boil down the solution, but once you get it down to around 400ml or so (from 1L of vinegar and ~35g CuO), you can let it cool and lots of the copper acetate precipitates as fine greenish crystals. I would use that method, personally. Regular distilled vinegar is actually quite pure, so if your copper compound is pure, you will get extremely high grade crystals...

Note: Let the vinegar/CuO suspension sit for a while, it all reacts in the end. Using a slight excess of vinegar may help aid this.

[Edited on 8-5-2006 by PainKilla]




View user's profile View All Posts By User
kazaa81
Hazard to Others
***




Posts: 368
Registered: 30-4-2004
Member Is Offline

Mood: ok

[*] posted on 8-5-2006 at 14:33


Is CuSO4 able to shift metallic Pb?
I mean, if I have a solution of CuSO4 and I put a sheet of metallic Pb, will I get PbSO4 and Cu?

CuSO4 (aq) + Pb (s) ---> Cu (s) + PbSO4 (aq)

or

CuCO3 (aq) + Pb (s) ----> Cu (s) + PbCO3 (aq)
View user's profile View All Posts By User
12AX7
Post Harlot
*****




Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline

Mood: informative

[*] posted on 8-5-2006 at 14:40


Well, no, those aren't soluble lead compounds. You'll get a layer of PbSO4 and that's that.

The second will never proceed under any circumstances, except possibly high pressure CO2. CuCO3 isn't soluble, so the best you could hope for would be fine powders and heat. But heat decomposes the carbonates, so it's not going to happen without a lot of help.

Tim




Seven Transistor Labs LLC http://seventransistorlabs.com/
Electronic Design, from Concept to Layout.
Need engineering assistance? Drop me a message!
View user's profile Visit user's homepage View All Posts By User This user has MSN Messenger
kazaa81
Hazard to Others
***




Posts: 368
Registered: 30-4-2004
Member Is Offline

Mood: ok

[*] posted on 8-5-2006 at 14:58


So, because lead soluble salts in H2O are just the ones of organic acids...

Ca(NO3)2 (aq) + CuSO4 (aq) -----> Cu(NO3)2 (aq) + CaSO4 (s)

Cu(NO3)2 (aq) + Pb (s) -----> Pb(NO3)2 (aq) + Cu (s)
View user's profile View All Posts By User
Pommie
Hazard to Self
**




Posts: 70
Registered: 6-2-2005
Location: Australia
Member Is Offline

Mood: No Mood

[*] posted on 10-5-2006 at 05:42


That works. However, the Calcium sulphate is a bitch to filter and the copper nitrate is a bitch to dry.

Go for a Cu(NO<sub>3</sub>;)<sub>2</sub> solution and throw some lead in.

If you are trying to plate lead dioxide electrodes then you want a 50/10 mix of lead/copper nitrate.

Mike.


[Edited on 11-5-2006 by Pommie]
View user's profile View All Posts By User

  Go To Top