Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Hot Plate Overnight
DFliyerz
Hazard to Others
***




Posts: 241
Registered: 22-12-2014
Member Is Offline

Mood: No Mood

[*] posted on 30-12-2014 at 12:38
Hot Plate Overnight


I'm planning to use an electrolysis cell to make potassium chlorate from potassium chloride, but due to the location of my lab (my garage), it will get very cold at night, even with 5 amps of power. Would it be safe to leave my hot plate on overnight, at warm or low settings?
View user's profile View All Posts By User
macckone
Dispenser of practical lab wisdom
*****




Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline

Mood: Electrical

[*] posted on 30-12-2014 at 14:10


It really depends on the quality of the hotplate.
Good ones can run continuously for years.

Ps. A cheap space heater may be preferable if the hotplate is questionable.

[Edited on 30-12-2014 by macckone]
View user's profile View All Posts By User
DFliyerz
Hazard to Others
***




Posts: 241
Registered: 22-12-2014
Member Is Offline

Mood: No Mood

[*] posted on 30-12-2014 at 14:16


The hotplate is an Aroma single burner, which so far has proven to be pretty good quality.
View user's profile View All Posts By User
gdflp
Super Moderator
*******




Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline

Mood: Staring at code

[*] posted on 30-12-2014 at 14:55


The problem wouldn't be the normal function of the hot plate, theoretically it should be fine. However, hot plates sometimes fail and spontaneously burst into flames, even at low temperatures. It even occurs when the hot plates are off, but still plugged in, though I would assume this is reasonably rare. Generally potassium chlorate cells get very hot, so the cell should keep itself warm overnight.
View user's profile View All Posts By User
violet sin
International Hazard
*****




Posts: 1482
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline

Mood: Good

[*] posted on 30-12-2014 at 15:56


how about a small 3$ styrofoam cooler around the vessel itself. you can get them at many grocery stores, they only hold enough food for a picnic or so. this doesn't actually address the hotplate issue, but it may help with the overall temp at night.
View user's profile View All Posts By User
forgottenpassword
Hazard to Others
***




Posts: 374
Registered: 12-12-2013
Member Is Offline

Mood: No Mood

[*] posted on 31-12-2014 at 13:56


Thousands of hotplates in thousands of laboratories are left on overnight on a daily basis.
View user's profile View All Posts By User
Fulmen
International Hazard
*****




Posts: 1721
Registered: 24-9-2005
Member Is Offline

Mood: Bored

[*] posted on 31-12-2014 at 14:44


A quality hotplate should withstand a few years of continuous service, we used a common "dorm-type" single burner and it ran on full power IIRC 24/7/365. But that was on a manned lab, unsupervised you should strive for as few powered devices as possible. Anything like a hot plate should be avoided if possible, and in your case the power output should be more than enough with some insulation. I'm currently running a 500ml cell at 4A/3,2V and it produces more than enough heat for this to work.
View user's profile View All Posts By User
g1ng3rbr34d_m4n
Harmless
*




Posts: 6
Registered: 4-1-2015
Member Is Offline

Mood: No Mood

[*] posted on 4-1-2015 at 12:00


You could stick a heating pad under your cell...
View user's profile View All Posts By User
unionised
International Hazard
*****




Posts: 5127
Registered: 1-11-2003
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 4-1-2015 at 13:58


Quote: Originally posted by DFliyerz  
it will get very cold at night, ?


It's not really my field.
Does it matter if the cell gets cold?
View user's profile View All Posts By User
Mailinmypocket
International Hazard
*****




Posts: 1351
Registered: 12-5-2011
Member Is Offline

Mood: No Mood

[*] posted on 5-1-2015 at 07:16


If there is sufficient current running through the cell it should not need external heating. Sometimes I have had to put the cell in a bowl of cool water to allow better heat dissipation because it was getting too hot to touch.

[Edited on 5-1-2015 by Mailinmypocket]
View user's profile View All Posts By User
Bert
Super Administrator
*********




Posts: 2821
Registered: 12-3-2004
Member Is Offline

Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".

[*] posted on 5-1-2015 at 08:31


There is a thing called "insulation".



Rapopart’s Rules for critical commentary:

1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.

Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).

View user's profile View All Posts By User
phlogiston
International Hazard
*****




Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline

Mood: pyrophoric

[*] posted on 5-1-2015 at 12:07


1. increase the distance between the electrodes
2. increase the voltage to restore the current to its previous level

This way you can increase the ohmic heating to any desired level
Normally, this is avoided as it is detrimental to efficiency (you are spending electric power on heating rather then electrolysis).

But first take Berts advice and add insulation.




-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer
View user's profile View All Posts By User
dermolotov
Hazard to Others
***




Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline

Mood: Free

[*] posted on 10-1-2015 at 13:09
Magic!


I do the same with my hotplate/stirrer (Corning PC 420) for overnight oxidation sometimes. Since it is outside, I put the heating on 1 or 2 in the winter and place it in a large belljar with the vacuum adapter open. This has prevented a sudden ignition of ether vapours before (not sure how that happened). It had obviously set on fire as the wood underneath was burnt.
Miraculously, the hot plate was fine.

Not sure how much belljars are... But it is worth the investment if you need to stir/ heat things like ether or hexanes solutions overnight.

[Edited on 10-1-2015 by dermolotov]
View user's profile Visit user's homepage View All Posts By User
Texium
Administrator
Thread Moved
22-11-2023 at 19:04

  Go To Top