Sciencemadness Discussion Board
Not logged in [Login ]
Search the forums Search   Frequently Asked Questions FAQ   View member list Member List   Today's Posts Today's Posts   Forum Stats Stats Back to: sciencemadness.org
Sciencemadness Discussion Board » Engineering and Equipment » Process Engineering » attach a stirring rod to a Talboy's stirring bodine motor Go To Bottom

Printable Version  
Author: Subject: attach a stirring rod to a Talboy's stirring bodine motor
obeliscus
Harmless
*



Posts: 12
Registered: 24-6-2016
Member Is Offline

Mood: No Mood

[*] posted on 21-7-2016 at 15:10
attach a stirring rod to a Talboy's stirring bodine motor

Hello
I have a Talboy's engineering bodine stirrer motor and found that my stirring rod does not attach nor fit snugly into the attachment fixture.
I sent a message to the ebay seller over this concern and I was told that I needed a 1/4 inch coupler.

I have looked at several types of 1/4 inch couplers and I am unsure as to which coupler would work.

I will attach photos of the rod and motor.







[Edited on 21-7-2016 by obeliscus]

IMG_1475.jpg - 280kBIMG_1474.jpg - 212kBIMG_1473.jpg - 226kB
View user's profile View All Posts By User
Magpie
lab constructor
*****



Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline

Mood: Chemistry: the subtle science.

[*] posted on 22-7-2016 at 06:04


I had to buy a chuck at Ace hardware, then an adapter atMcMaster-Carr mail order. my mixer is not a Talboy, however.



The single most important condition for a successful synthesis is good mixing - Nicodem
View user's profile View All Posts By User
obeliscus
Harmless
*



Posts: 12
Registered: 24-6-2016
Member Is Offline

Mood: No Mood

[*] posted on 22-7-2016 at 07:58


Do you know what sort of chuck?
View user's profile View All Posts By User
Magpie
lab constructor
*****



Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline

Mood: Chemistry: the subtle science.

[*] posted on 22-7-2016 at 13:33
Correction: Jacobs

Jacobsen iirc.

[Edited on 23-7-2016 by Magpie]



The single most important condition for a successful synthesis is good mixing - Nicodem
View user's profile View All Posts By User
obeliscus
Harmless
*



Posts: 12
Registered: 24-6-2016
Member Is Offline

Mood: No Mood

[*] posted on 23-7-2016 at 19:45


Thanks I will go check it out.
View user's profile View All Posts By User
Magpie
lab constructor
*****



Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline

Mood: Chemistry: the subtle science.

[*] posted on 24-7-2016 at 13:03


3D printer shaft coupling may be useful. Also see:

http://www.walmart.com/ip/TALBOYS-191C-Talboys-Jacobs-Chuck-...


[Edited on 25-7-2016 by Magpie]



The single most important condition for a successful synthesis is good mixing - Nicodem
View user's profile View All Posts By User
obeliscus
Harmless
*



Posts: 12
Registered: 24-6-2016
Member Is Offline

Mood: No Mood

[*] posted on 24-7-2016 at 20:13


update:

I just discovered after 3 test uses that my motor has died; it looks like I will have to get a new one.
View user's profile View All Posts By User
Texium
Administrator
 Thread Moved
27-11-2023 at 10:42

 Sciencemadness Discussion Board » Engineering and Equipment » Process Engineering » attach a stirring rod to a Talboy's stirring bodine motor   Go To Top