dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
dioxane gunk removal
Hi I made dioxane from ethylene glycol and sulfuric acid in June and distilled it once and kept the distillate.
Last week I distilled it a second time and when the distillation was over much gunk remained in the flask; I added sulfuric acid to dissolve this
gunk. The gunk did not dissolve so I heated it in a far away outside fireplace ; it did not dissolve but the contents overflowed.
Now the gunk is stuck to the flask; is it possible to dissolve it in concentrated NaOH or would another method be better.
|
|
|
BromicAcid
International Hazard
Posts: 3227
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Ehhh, what a mess. I would go mechanical removal before trying with 'solvents' again, likely you just have carbonized junk which will not dissolve in
much of anything. I would be reluctant to use Piranha on it since you likely have plenty of more readily oxidizeable garbage in there which can lead
to problems. What size is the flask, it's hard to tell. A wooden doll rod is a good place to start because if you slip you likely will not punch a
hole in your flask.
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
1000 ml
|
|
|
unionised
International Hazard
Posts: 5104
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
This sort of thing helps.
http://www.lakeland.co.uk/8949/Magic-Copper-Balls-For-Cleani...
If you dig most of the char out with a spatula or something then swirl the copper beads round they scour out quite a lot more.
You will probably end up using something like boiling H2SO4 to get the last of the junk out.
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
Would boiling the junk with H2SO4 turn it into carbon dioxide? What about piranha?
|
|
|
unionised
International Hazard
Posts: 5104
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
At a high enough temperature
C + 2 H2SO4 --> CO2 +2SO2+ 2 H2O
(at that temperature you are pretty near the point where C + O2 --> CO2 and also near the pint where the glass melts)
Piranha works too
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
sulfuric acid would be a gas most likely at atmospheric pressure
|
|
|
BromicAcid
International Hazard
Posts: 3227
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Instead of copper balls I have used rock salt and methanol to shake around in flasks to abrade the gunk off the walls.
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Apply physical methods.
Then, run a much less physical and more advanced photochemical or Fenton reaction to produce hydroxyl radicals in the presence of hydrogen gas (best
under pressure) to attack the carbon. Place in sunlight and let it sit for some time.
Reference:
April 1975, Vol.13(2):115–124, doi:10.1016/0008-6223(75)90268-7, link http://www.sciencedirect.com/science/article/pii/00086223759... to "The reaction of hydroxyl radicals with carbon at 298 K", by M.F.R. Mulcahy and
B.C. Young.
Logic: Both the hydroxyl radical and the hydrogen atom radical (from the action of the hydroxyl radical on H2) attack carbon.
Sample embodiment: Place a very small amount of Zinc metal in a large excess of cheap HCl or H2SO4 together with sheets or bars of Iron and Copper.
Seal after venting out air to form a pressurized hydrogen atmosphere. Place in sunlight.
-------------------------------
Another idea, not as gaseous but full of juice. Make an electrode with say a stainless steel ball soldered on to an insulated copper wire. The other
electrode is copper that is positioned in the middle of the flask. Rest the ball/electrode on the carbon surface and move it around as needed during
an electrolysis (using a battery source) of an electrolyte of, say, aqueous MgSO4. My experience with graphite is that is it just falls apart in the
process of making CuSO4 and a white precipitate of Mg(OH)2.
[Edited on 24-10-2016 by AJKOER]
|
|
|
woelen
Super Administrator
Posts: 7977
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
K2Cr2O7 (or CrO3) with concentrated H2SO4 and then heating this in the flask. This dissolves many difficult to remove organic/carbonized compounds. It
is more toxic than piranha solution, but much safer to use, because there is no risk of explosion.
Piranha solution is much better from an environmental point of view. You can mitigate the waste issue somewhat by dissolving the orange
acid/hexavalent chromium mix in water and adding sodium metabisulfite until the color is purely green with a bluish hue. If that point is reached you
have trivalent chromium. You can flush that down the drain with a lot of water.
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
Thanks for the replies.
I would have responded much sooner but I got stuck with work and later sick.
The dissolution in piranha acid seem slow to a degree when I added it. A majority of the product I suspect is carbon since I dont believe piranha
oxidized elemental carbon well.
|
|
|
DraconicAcid
International Hazard
Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
If I have carbonized gunk in a flask, I usually put a bit of nitric acid in it, and hit it with a bunsen burner.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
CuReUS
National Hazard
Posts: 928
Registered: 9-9-2014
Member Is Offline
Mood: No Mood
|
|
did you use 30% H2O2 ? Did you use the right ratio ?
https://www.youtube.com/watch?v=cLpSapjKcxM
|
|
|
wildyams
Harmless
Posts: 1
Registered: 3-12-2016
Member Is Offline
Mood: No Mood
|
|
I bet some copper coated metal BB's would work just as well, and you could probably pick them up at the closest big store.
|
|
|
DFliyerz
Hazard to Others
Posts: 241
Registered: 22-12-2014
Member Is Offline
Mood: No Mood
|
|
I think Praixchys used acetone in one of his videos to clean it.
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
I'll second Woelen's idea. Chromic acid is very effective at getting rid of nasty organic residues, not just by reacting but by physically detaching
them from the flask. And while you're at it you may as well reduce the leftover hexavalent chromium with some ethanol and add sodium carbonate to
precipitate chromium(III) hydroxide which is fun to have around.
|
|
|
Chlorine
Hazard to Self
Posts: 56
Registered: 26-11-2016
Location: Maine, USA
Member Is Offline
Mood: Brominated
|
|
I personally use store bought copper coated steel BB's. Swirl them around the flask with 10=15 mls of water then use a strong magnet to get them out
of the carbon water solution.
|
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
I'm not terribly good at maths but...
H2SO4 + H2O2 (or K2Cr2O7) + danger involved and time spent in cleaning = more than than what I'd pay for a new RBF
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
@CuReUS
The concentration was 15%; this likely was one of my issues.
Attachment: ja01450a002.pdf (472kB)
This file has been downloaded 316 times
|
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
ignore the attachment
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
Anything strongly oxidizing in combination with sulfuric acid and strong heating should work. You can try dichromates, permanganates, H2O2, nitrates,
and persulfates. Always use these mixtures with extreme caution. Certain organic materials form explosive mixtures with these strong oxidizers.
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Hot NaOH solution seems to be very good, not at dissolving this kind of gunk, but physically detaching it from the glass surface. I often do this and
then use a sharp tool to kind of break up the stuff so that it can fit through the glass joints out of the flask.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
