methyleneblue
Harmless
Posts: 7
Registered: 19-3-2017
Location: NSW, Australia
Member Is Offline
Mood: No Mood
|
|
Using an erlenmeyer flask for refluxing
Hi all,
I'm going to be doing a Fischer-Speier Esterification tomorrow, probably some Isopropyl Acetate. My only issue is, and partially due to laziness, is
that I don't have a mantle yet, and can't be bothered setting up an oil bath on the hot plate for a round-bottom flask.
Is it possible to just stick an erlenmeyer underneath a condenser, sit it straight on the hot plate and reflux that way? Or does that do some
witchcraft to the reaction and stuff it up? 
PS: Yes, I am using glass joints. The flask and condenser are connected, not just sitting above one another.
[Edited on 29-3-2017 by methyleneblue]
MethyleneBlue.
|
|
|
PirateDocBrown
National Hazard
Posts: 570
Registered: 27-11-2016
Location: Minnesota
Member Is Offline
Mood: No Mood
|
|
How do you propose keeping the vapor from escaping between the condenser and the flask? Or is it an Erlenmeyer with a glass joint?
|
|
|
methyleneblue
Harmless
Posts: 7
Registered: 19-3-2017
Location: NSW, Australia
Member Is Offline
Mood: No Mood
|
|
Woops. 
Yep, 24/40 glass joints all the way.
MethyleneBlue.
|
|
|
j_sum1
Administrator
Posts: 6220
Registered: 4-10-2014
Location: Unmoved
Member Is Online
Mood: Organised
|
|
I don't see any particular issues. The only thing is that the shape of an Erlenmeyer lends itself to greater thermal stresses with uneven heating.
And you will get uneven heating. The Erlenmeyer will also tend to reflux in the flask -- which could be a good thing or a bad thing depending.
Bottom line, ok unless you are doing something high temp.
|
|
|
methyleneblue
Harmless
Posts: 7
Registered: 19-3-2017
Location: NSW, Australia
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by j_sum1  | I don't see any particular issues. The only thing is that the shape of an Erlenmeyer lends itself to greater thermal stresses with uneven heating.
And you will get uneven heating. The Erlenmeyer will also tend to reflux in the flask -- which could be a good thing or a bad thing depending.
Bottom line, ok unless you are doing something high temp. |
Alright sounds good, Isopropyl Acetate boils at 89°C anyway so I should be fine.
Thanks.
MethyleneBlue.
|
|
|
j_sum1
Administrator
Posts: 6220
Registered: 4-10-2014
Location: Unmoved
Member Is Online
Mood: Organised
|
|
Well at that temp you could easily rig up a water bath. Far less messy than an oil bath IMO and having a ceiling temperature and a bit of thermal
ballast makes the process easy to control.
|
|
|
methyleneblue
Harmless
Posts: 7
Registered: 19-3-2017
Location: NSW, Australia
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by j_sum1 | | Well at that temp you could easily rig up a water bath. Far less messy than an oil bath IMO and having a ceiling temperature and a bit of thermal
ballast makes the process easy to control. |
Ooo I like that idea.
Will also look into this. Thankyou! 
MethyleneBlue.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1636
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
I've used brine solutions for this sort of work too, helps suppress waters boiling point making it higher. Some thing for ya to look into.
|
|
|
methyleneblue
Harmless
Posts: 7
Registered: 19-3-2017
Location: NSW, Australia
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by XeonTheMGPony | | I've used brine solutions for this sort of work too, helps suppress waters boiling point making it higher. Some thing for ya to look into.
|
Are you talking about in the actual beaker? Because if so, wouldn't this react with the Alcohol, Carboxylic acid and Catalytic acid and do some crazy
reactions?
MethyleneBlue.
|
|
|
Tsjerk
International Hazard
Posts: 3022
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
He is talking about the water bath, it will be a bit safer towards boiling to dryness with the electrical heating set to the same output of heat . You
can also put more energy into the reaction, but I don't know if that is necessary. Especially if you use IPA in excess.
[Edited on 30-3-2017 by Tsjerk]
|
|
|
PirateDocBrown
National Hazard
Posts: 570
Registered: 27-11-2016
Location: Minnesota
Member Is Offline
Mood: No Mood
|
|
Erlenmeyer, condenser, and hot plate are pretty much exactly how I do such things. Water bath, if the temp is low enough. Sometimes a flatbottom round
flask. But yeah, all 24/40.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1636
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Tsjerk | He is talking about the water bath, it will be a bit safer towards boiling to dryness with the electrical heating set to the same output of heat . You
can also put more energy into the reaction, but I don't know if that is necessary. Especially if you use IPA in excess.
[Edited on 30-3-2017 by Tsjerk] |
You nailed it.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
