Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Hydrochloric Acid from Toilet Cleaner
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 17-7-2018 at 13:01
Hydrochloric Acid from Toilet Cleaner


I know that many brands of toilet bowl cleaner contain about a 10% solution of hydrochloric acid. It is hard to get cheap HCl where I live, but I was wondering if I could just distill the HCl off from the toilet cleaner and leave all of the surfactants and
dyes behind. I know people do this with sulfuric acid from draim cleaner, but HCl exists as the gas hydrogen chloride. Would the water distil over with it to give me a solution or would I end up flooding my lab with hydrogen chloride gas?


image.jpg - 1.2MB




List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User
DraconicAcid
International Hazard
*****




Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline

Mood: Semi-victorious.

[*] posted on 17-7-2018 at 13:17


The water should also distill over. That being said, it's always a good idea to make sure you have proper ventilation anyway.



Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
View user's profile View All Posts By User
JJay
International Hazard
*****




Posts: 3440
Registered: 15-10-2015
Member Is Offline


[*] posted on 17-7-2018 at 13:51


The water and some HCl will distill over first, and the concentration will gradually increase to the azeotropic concentration. Once you reach the azeotropic concentration, the temperature and concentration will plateau.

You won't need any special ventilation unless you accidentally flash boil some HCl or let your condenser get hot, but good ventilation is a good idea anyway.




View user's profile View All Posts By User
Cipher
banned
*




Posts: 9
Registered: 17-7-2018
Location: woelen disabled my posting and u2u privilegies
Member Is Offline

Mood: woelen disabled my posting and u2u privilegies

[*] posted on 17-7-2018 at 14:10


And if you care more about safety than concentration, best to distill it into some water, so gas will more likely dissolve.
Hope you are ready to deal with back-flow if it will occur.
View user's profile View All Posts By User
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 17-7-2018 at 14:34


I was planning on having some distilled water in the collection flask anyways. Ive heard of people doing similar things with formic acid from oven cleaner and flooding their labs with fumes so yes, safety over concentration.



List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User
happyfooddance
National Hazard
****




Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline

Mood: No Mood

[*] posted on 17-7-2018 at 14:49


If your acid is under 20.2% by weight, there is a precisely 0.0% chance of suckback.

For safety, I would just do a titration (however crude) to make sure.

There is no reason to put water in the recieving flask.
View user's profile View All Posts By User
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 17-7-2018 at 14:58


When I get a chance, I will do a titration. By weight the Lysol toilet cleaner I plan to use is supposed to be 12% by weight. I honestly am expecting it to be plus or minus 6%. Lucky for me, I don't need concentrated HCl.



List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User
CharlieA
National Hazard
****




Posts: 645
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline

Mood: No Mood

[*] posted on 17-7-2018 at 15:43


Quote: Originally posted by happyfooddance  
If your acid is under 20.2% by weight, there is a precisely 0.0% chance of suckback.



I must be missing something here; what is the relationship of composition to suckback?
View user's profile View All Posts By User
happyfooddance
National Hazard
****




Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline

Mood: No Mood

[*] posted on 17-7-2018 at 17:19


Quote: Originally posted by CharlieA  
Quote: Originally posted by happyfooddance  
If your acid is under 20.2% by weight, there is a precisely 0.0% chance of suckback.



I must be missing something here; what is the relationship of composition to suckback?


Suckback is caused by gases (like HCl) which are highly soluble in a liquid, and said gases being evolved at a slower rate than they are adsorbed, thus creating a vacuum.

But we are not talking about HCl(g), we are talking about aqueous HCl, which forms a maximum boiling (108.5°C) azeotrope with water that is 20.2% HCl by weight. If you boil a solution that is less than 20.2%, as JJay mentioned it will come over in a lower concentration than what is in the boiling pot until the concentration of the boiling pot reaches 20.2%. So unless you are distilling concentrated HCl there is no way to get HCl(g), hence no suckback.

Also, if he is distilling in a normal setup, not a bubbler, there is no possibility of suckback anyway... Just putting a little water in a recieving flask can never cause suckback.
View user's profile View All Posts By User
Metacelsus
International Hazard
*****




Posts: 2531
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline

Mood: Double, double, toil and trouble

[*] posted on 17-7-2018 at 18:36


Toilet bowl cleaner often contains thickeners and surfactants, in addition to HCl. (Different brands may vary.) Distillation might cause a lot of foaming, so you should use an appropriately sized vessel.



As below, so above.

My blog: https://denovo.substack.com
View user's profile View All Posts By User
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 17-7-2018 at 20:07


Quote: Originally posted by Metacelsus  
Toilet bowl cleaner often contains thickeners and surfactants, in addition to HCl. (Different brands may vary.) Distillation might cause a lot of foaming, so you should use an appropriately sized vessel.


Good Idea. Strong stirring would be a good idea as well to keep foaming to a minimum. Would boiling stones be necessary?




List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User
happyfooddance
National Hazard
****




Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline

Mood: No Mood

[*] posted on 18-7-2018 at 12:07


Quote: Originally posted by Abromination  

Good Idea. Strong stirring would be a good idea as well to keep foaming to a minimum. Would boiling stones be necessary?


Boiling stones aren't necessary if you have decent stirring; however, a few small ones shouldn't hurt (as long as they don't interfere with the stirring).
View user's profile View All Posts By User
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 18-7-2018 at 15:15




Boiling stones aren't necessary if you have decent stirring; however, a few small ones shouldn't hurt (as long as they don't interfere with the stirring).[/rquote]

Now that I think of it, the stir bar would act rather like a boilingstone itself. Also, you have a fair point. It would be difficult to use boiling stones with a stir bar.




List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User
VSEPR_VOID
National Hazard
****




Posts: 719
Registered: 1-9-2017
Member Is Offline

Mood: Fullerenes

[*] posted on 18-7-2018 at 16:20


I recommend buying some sodium bisulfate or sulfuric acid. Distilling a dry mixture of bisulfate, or concentration sulfuric acid, will yield hydrogen chloride. It would be much faster and cheaper than toilet bowl cleaning.

https://www.ebay.com/itm/Sodium-Bisulfate-NaHSO4-Minimum-of-...

https://www.ebay.com/itm/Pool-Breeze-Sodium-Bisulfate-Swimmi...




Within cells interlinked
Within cells interlinked
Within cells interlinked
View user's profile View All Posts By User
TesTube
Harmless
*




Posts: 1
Registered: 18-7-2018
Member Is Offline


[*] posted on 18-7-2018 at 18:11


Quote: Originally posted by VSEPR_VOID  
I recommend buying some sodium bisulfate or sulfuric acid. Distilling a dry mixture of bisulfate, or concentration sulfuric acid, will yield hydrogen chloride. It would be much faster and cheaper than toilet bowl cleaning.

https://www.ebay.com/itm/Sodium-Bisulfate-NaHSO4-Minimum-of-...

https://www.ebay.com/itm/Pool-Breeze-Sodium-Bisulfate-Swimmi...


I think you forgot something :o
View user's profile View All Posts By User
Abromination
Hazard to Others
***




Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline

Mood: 1,4 tar

[*] posted on 18-7-2018 at 23:10


[rquote I think you forgot something :o[/rquote]

I agree:)




List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
--------------
View user's profile View All Posts By User

  Go To Top