Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
 Pages:  1  
Author: Subject: Ammonia Generator/Ammonia in Methanol
smuv
National Hazard
****




Posts: 842
Registered: 2-5-2007
Member Is Offline

Mood: Jingoistic

[*] posted on 16-4-2011 at 19:07
Ammonia Generator/Ammonia in Methanol


[Tweet]I'm getting board babysitting my ammonia generator, might as well post about it.[/Tweet]

In a very web 2.0 way, I will post about something as I am doing it :D.

I need a dry solution of NH3 in methanol, I can't think of any double displacement reactions that would conveniently produce this without also producing water (aside from resorting to alkoxides), so I setup a little ammonia generator and am bubbling the stuff through methanol. I am pleasantly surprised by how smoothly things are going. So far, my basement doesn't smell like ammonia. :)

Reagents:
350 mL MeOH (dissolves 3.3 mol NH3 @ 25c)
325g Ammonium Sulfate (~2.5 mol)
250g Sodium Hydroxide (~7 mol)
~7 mL 10% NH3(aq)



The setup, generating away

The setup is fairly self explanatory. The ammonia is generated in the left bottle, it passes through a cooled gas dryer (filled with KOH), it goes on to pass through an automotive PCV valve (check valve) and is bubbled through the cooled methanol using a pipette. Also, the right bottle looks capped, it is only loosely so (although I played with capping it, it does not build positive pressure...so long as the ammonia is dissolving...).

The reaction was setup by adding the ammonium sulfate and NaOH, but not mixing them, letting them layer (I did mine sulfate above NaOH. This is fine, but I think it would work even better the other way around). This mixture is metastable, it doesn't produce much ammonia as is. Next the aqueous ammonia was added and the generator bottle was quickly capped. At this point, not much ammonia is produced, but upon shaking the generator and mixing the reagents, it really gets going. The rate of ammonia production can be easily regulated by how frequently you shake it. Right now I have a good rate of production, I am shaking maybe every ~7 min as I hear the rate of production slacken.

Here are some more pictures of the different parts of the aparatus.



Production bottle (material HDPE)



Here is how a good seal is made using the original gasket (with a hole drilled through the center), the quarter is made of Nickel/copper, the tubing is 304 SS and the solder used was tin silver (the quarter and solder are probably susceptible to attack by ammonia).



This is the gas dryer, I was gonna make it out of PVC, but after pricing all the parts and fittings I found I could make it cheaper from iron pipe, I also use this piece as my vacuum drier/cold trap. The solder is 60/40 Sn/Pb and the tubing is 304 SS.



[Edited on 4-17-2011 by smuv]




"Titanium tetrachloride…You sly temptress." --Walter Bishop
View user's profile View All Posts By User
#maverick#
Hazard to Others
***




Posts: 209
Registered: 7-4-2011
Member Is Offline

Mood: hybridised

[*] posted on 16-4-2011 at 21:21


Very interesting concept I like it. Would u mind if I pm u as I am building if I have any questions
View user's profile View All Posts By User
bbartlog
International Hazard
*****




Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline

Mood: No Mood

[*] posted on 17-4-2011 at 05:36


I like the detail shot of the fitting you made from SS tubing and a quarter. I'll have to try that sometime.
View user's profile View All Posts By User
smuv
National Hazard
****




Posts: 842
Registered: 2-5-2007
Member Is Offline

Mood: Jingoistic

[*] posted on 17-4-2011 at 17:39


It all went pretty well, except it took a long time, I think next time I will either add more water/aqua ammonia or even heat the generator bottle to ~40c to make sure that the sodium sulfate produced doesn't soak up all the water. No issues with suck-back, but this setup didn't really test the PCV valve. Tough I think the pcv valve does leak a little bit against flow (I tested a new one, it does the same), so it may only slow suck-back.

Somewhat related, I went to walmart today and was browsing their surprisingly well stocked aquarium department to see what I might be able to find. I ended up finding/buying a check valve (for air-stones apparently) and these really small ~1.5cm diamater 2cm tall airstones. One thing though, the check valve needs like 5psi to fully open (allows slow flow at ~0.5psi)...so if it were used in a gas generator it would definitly run at slightly elevated pressure.

Anyways, stay tuned for ammonia generator 2.0 :D

Maverick + bbartlog, I'm glad you like my little ammonia generator. Feel free to ask questions.




"Titanium tetrachloride…You sly temptress." --Walter Bishop
View user's profile View All Posts By User
Bot0nist
International Hazard
*****




Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline

Mood: Streching my cotyledons.

[*] posted on 17-4-2011 at 20:42


Very nice setup smuv! Have you tried lowering your final ice baths temp(w/ dry ice) and condensing any NH<sub>3</sub> with this setup?



U.T.F.S.E. and learn the joys of autodidacticism!


Don't judge each day only by the harvest you reap, but also by the seeds you sow.
View user's profile View All Posts By User
Arthur Dent
National Hazard
****




Posts: 553
Registered: 22-10-2010
Member Is Offline

Mood: entropic

[*] posted on 18-4-2011 at 03:50


Nice setup! I've been looking into Woelen's ammonia generator setup also but am hesitant to attempt because I can only do this indoors and a runaway reaction would be quite bad. Since you say that the reaction is not intense and out of control, I might try it out.

I have a small ball valve (just a small plastic cage with a tiny ball rattling in it) that you can insert in a transparent PVC tube, but I think this works better with liquids rather than gases. I've been to a pet shop and saw the tubing and valves there but they're so small that I could never fit the minuscule tubing on regular-sized glassware ports and barbs. I'll look into automotive check valves...

On the other hand, I could just add an empty erlenmayer with a side port as an anti-suckback prevention method, right?

Robert





--- Art is making something out of nothing and selling it. - Frank Zappa ---
View user's profile View All Posts By User
Ephoton
Hazard to Others
***




Posts: 463
Registered: 21-7-2005
Member Is Offline

Mood: trying to figure out why I need a dark room retreat when I live in a forest of wattle.

[*] posted on 18-4-2011 at 05:24


now thats getto :)

when ive generated ammonia I have used a glass rig so hats off to ya.

the way ive done it is to have aqua caustic refluxing in a two neck flask with aqua ammonia salt
being dripped into the caustic.

the solution was stirred at all times.

there was a vacuum adapter with stopper put in the end of it slotted into the top of the condensor.

the vacuum nipple is then led to the KOH drying bottle like you have via a tube which is then
led to flask to gas or condense after being passed through a trap.

this pritty much does that except you are not refluxing a solution or dripping a solution.

I would personaly be a little scared of two solids like that being put in a flask then adding a liquid
to get gas.

when one refluxes caustic then drips in saturated ammonia salt solution into it you get a smooth
release of gas.

a final trap then hcl gas capture bottle will then guarentee you get no smells.




e3500 console login: root
bash-2.05#

View user's profile View All Posts By User
cyanureeves
National Hazard
****




Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline

Mood: No Mood

[*] posted on 18-4-2011 at 11:22


my setup looks like a district 9 reproduction shack compared to this. hamilton beach coffee makers use a one way check valve inside one of the brewing hoses and is exactly the same size as your tubing. is ammonia in methanol an old process?does it just smell like ammonia and not methanol or is it a totally different thing? is it ammonium hydroxide?flammable?what is it?.......interesting!:o:o
View user's profile View All Posts By User
smuv
National Hazard
****




Posts: 842
Registered: 2-5-2007
Member Is Offline

Mood: Jingoistic

[*] posted on 18-4-2011 at 11:43


@Arthur: You're right, ball type check valves are usually better for liquids, reed valves are better for gases. I wouldn't worry too much about hose sizes, after all, aquarium air-stones use these small fittings, and that would probably be the best thing to use as a bubbler (probably way better than a pipette).

Erlenmeyer is fine, but I just wanted to avoid using another flask and having another set of leaks to deal with.

@Bot: I'll save that one for you to try. :) You would need to get the rate of generation up though before attempting this.

@cyanureeves: haha, Ephoton calls it ghetto you call it Hamilton beach. Ammonia and methanol is just like ammonia in water, simply a solution. Ammonia in water contains very little "NH4OH" and is 99% just NH3 dissolved in water. Likewise ammonia in methanol is 99% dissolved NH3 with a small amount of "NH4OMe". But to be honest, I hate how even in literature NH3(aq) is referred to as NH4OH; this only confuses people. Yes it smells like ammonia and methanol, but mostly ammonia. :D

@Ephoton: Damn E, next time I'll just have to make it out of platinum and unicorns to please you. ;)

I have all the glassware to do this (except the gas drier wouldn't have been pretty), but I didn't want to muck up my glass with the caustic in the generator and drier; so plastic and steel are the way to go IMO. I heavily considered the aqua ammonia route, but I only can get 10% ammonia at prices reasonable for generation, so I was worried that it wouldn't be concentrated enough.

Anyways, thanks for the positive feedback, stay tuned I need to make more ammonia so I'll definitely refine the process and my apparatus a little.




"Titanium tetrachloride…You sly temptress." --Walter Bishop
View user's profile View All Posts By User
smuv
National Hazard
****




Posts: 842
Registered: 2-5-2007
Member Is Offline

Mood: Jingoistic

biggrin.gif posted on 18-4-2011 at 20:47
Ammonia Generator 2.0


Hate to double post, but I AM SO PLEASED WITH MY AMMONIA GENERATOR!

The changes are:

Aquarium check valve: I used an air compressor to compare it to the pcv valve, reverse flow, this thing doesn't leak at all. The pcv valve...leaks, even a new one. Although, the aquarium check valve does cause the system to run at a bit of a positive pressure...BE WARNED.

Switched generator bottle: I did a rigorous pressure test of my old bottle, it leaked a little, really not much, but still a little. This one is made from plastic tubing glued through the cap of the bottle (with JB Weld...essentially epoxy).

Aquarium Airstone + stirring the reciever: Much more efficient gas capture, nuff said.

Modified reagent quantities/procedure:

To the generator bottle, 475 g (3.5 mol) ammonium sulfate were added followed by 50 mL NH3(aq). Next, 225 g (5.63 mol) of NaOH was added and the bottle was capped. In this state the generator did not produce much ammonia. The reagents were mixed by shaking. The rate of production could be regulated by how well the reagents were mixed.

With the new procedure the rate of ammonia production is much faster; the generator can be pushed to overwhelm the gas absorption setup, even though gas absorption is more efficient than the previously. Anyways, I am happy. :D



The setup. Don't get confused by the vac filtration going on nearby


This is the gas receiver, notice I use an insulated wire to prop up the airstone away from the stirbar, while still achieving good immersion. Bare wire CANNOT be used, copper is attacked by ammonia...




"Titanium tetrachloride…You sly temptress." --Walter Bishop
View user's profile View All Posts By User
#maverick#
Hazard to Others
***




Posts: 209
Registered: 7-4-2011
Member Is Offline

Mood: hybridised

[*] posted on 18-4-2011 at 22:00


nice updates included in my drawings now lets see if my handycraft incompetent ass can build it lol
View user's profile View All Posts By User
smuv
National Hazard
****




Posts: 842
Registered: 2-5-2007
Member Is Offline

Mood: Jingoistic

[*] posted on 18-4-2011 at 22:58


Sorry for my post-whoreyness, but this is just cool; look at the volume change after saturation! This started as 350mL of MeOH! I gotta keep this in the freezer, this thing is gonna blow up if I let it come to room temp.




@Mav: One thing to keep in mind is you setup the gas drier like this.




"Titanium tetrachloride…You sly temptress." --Walter Bishop
View user's profile View All Posts By User
12332123
Harmless
*




Posts: 38
Registered: 14-11-2009
Member Is Offline

Mood: No Mood

[*] posted on 19-4-2011 at 04:12


On a relatively unrelated note, does anyone know of any suppliers who sell those rubber septa to amateurs?
View user's profile View All Posts By User
#maverick#
Hazard to Others
***




Posts: 209
Registered: 7-4-2011
Member Is Offline

Mood: hybridised

[*] posted on 19-4-2011 at 16:10


if it is possible could i get a picture of the inside of the drying apparatus so i can the design of the inside, im not very good at building things lol, i need to very detailed lo0l
View user's profile View All Posts By User
Bot0nist
International Hazard
*****




Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline

Mood: Streching my cotyledons.

[*] posted on 20-4-2011 at 07:38


I believe he posted a link to a pic of the drying tube. In the pic it seems to use a glass apparatus. I'm sure that could be improvised though. My understanding is that the wet gas flows to the bottom of the drying tube and is then forced though the drying agent (KOH) and is then collected out of the top. The key is to get the gas to flow through as much KOH as possible before collecting.



[Edited on 20-4-2011 by Bot0nist]

[Edited on 20-4-2011 by Bot0nist]




U.T.F.S.E. and learn the joys of autodidacticism!


Don't judge each day only by the harvest you reap, but also by the seeds you sow.
View user's profile View All Posts By User
#maverick#
Hazard to Others
***




Posts: 209
Registered: 7-4-2011
Member Is Offline

Mood: hybridised

[*] posted on 20-4-2011 at 08:15


ahh i see
View user's profile View All Posts By User
TheWire
Harmless
*




Posts: 6
Registered: 27-4-2011
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 27-4-2011 at 17:36


Brilliant! I've been thinking of building one of these for a while but(maybe I'm being a bit ambitious/playing with fire) I wanted to collect the gas/neat NH3 rather than having it saturated in a solvent. I need a container that can hold 200PSI or keep the whole thing below -33C(or is it -22C?).

I have thought about using on old fire extinguisher as the main holding tank, inline /i would have coils(not copper) immersed in dry ice as will be the holding tank, I am not sure about a dryer yet and what form it would take but I'll think of something.

I would like to use glassware but the highest pressure vessels I have are my vaccum flasks and I don't think they'll cut it.....

I am under no illusion this stuff is dangerous, I may, after all just saturate a solvent with it, safer.


[Edited on 28-4-2011 by TheWire]
View user's profile View All Posts By User
bbartlog
International Hazard
*****




Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline

Mood: No Mood

[*] posted on 27-4-2011 at 18:10


The old aluminum fire extinguisher canisters I have claim to have been tested to 300psi. I'd look at the ones you have and see whether there is any fine print on them that might provide a clue as to their burst pressure. That said, you should also evaluate the compatibility of the materials with NH3.
Glassware just isn't a good choice for larger-scale pressure storage. On a small scale, ampoules and sealed tubes can sustain quite a bit of pressure, and even a decent beer bottle *should* be able to withstand 200psi; but glass does not fail safe and has somewhat of a tendency to hard-to-detect defects, which is just one of the reasons why metal gets used for storing stuff under pressure.
View user's profile View All Posts By User
Bot0nist
International Hazard
*****




Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline

Mood: Streching my cotyledons.

[*] posted on 27-4-2011 at 21:16


Its boiling point is -33.34 Celsius.


[Edited on 28-4-2011 by Bot0nist]




U.T.F.S.E. and learn the joys of autodidacticism!


Don't judge each day only by the harvest you reap, but also by the seeds you sow.
View user's profile View All Posts By User
condennnsa
Hazard to Others
***




Posts: 217
Registered: 20-4-2010
Location: Romania
Member Is Offline

Mood: No Mood

[*] posted on 27-4-2011 at 21:35


damn, smuv, you're a master do-it-yourselfer. The way you cleverly use normal household objects to create complex systems for synthesis is just amazing.
I'd also like to try this, but don't have ammonium sulfate, I have though 10+ kgs ammonium nitrate. I figure it'd also work with this. I do remember that when NH4NO3 and NaOH powders are mixed without any water there is a strong generation of ammonia right away.
View user's profile View All Posts By User
smaerd
International Hazard
*****




Posts: 1262
Registered: 23-1-2010
Member Is Offline

Mood: hmm...

[*] posted on 7-11-2011 at 14:58
check my set up :D


I'm about to have a go at this tomorrow, before I do I'd like a thumbs up or a thumbs down on my set-up :). It's probably hard to see but in the graduated cylinder there is a small pipet for a nozzle. It may not disperse perfectly but I am checking for a weight increase and a bit of excess is no problem.

DSCF0206.JPG - 107kB

Now I've done this before in a mason jar but with a large excess of reactants, a small amount of water to solvate it, and no requirement for dry gas. This time when I try this, of course I will have the receiving vessel in a salt/ice-bath and it will be done OUTDOORS.

This time around I am bubbling it into 95% ethanol for an attempt to synthesize triethylamine(and friends :P).

I'm mostly worried about the drying chamber. I have CaCl2 granules in there(the center vessel), if they get wet won't they clog the tube? Maybe I should put a very light and fluffy layer of cotton balls underneath the outlet to prevent this? I'd use NaOH, but it's quite costly, even if it means CaCl2 will yoink some of the gas.

Also worried about suck-back(which did happen last time).

[Edited on 7-11-2011 by smaerd]




View user's profile View All Posts By User
S.C. Wack
bibliomaster
*****




Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline

Mood: Enhanced

[*] posted on 7-11-2011 at 16:19


Quote: Originally posted by smaerd  

I'm mostly worried about the drying chamber. I have CaCl2 granules in there...I'd use NaOH, but it's quite costly, CaCl2 will yoink some of the gas.


Or most of it, whichever. Soda-lime (a bit too broad a term but is apparently ok when prepared by whatever method) is less expensive and can be used in both generation and drying.

Perhaps some books would be helpful in general.




"You're going to be all right, kid...Everything's under control." Yossarian, to Snowden
View user's profile Visit user's homepage View All Posts By User
smaerd
International Hazard
*****




Posts: 1262
Registered: 23-1-2010
Member Is Offline

Mood: hmm...

[*] posted on 7-11-2011 at 16:34


Yea I guess I should have looked more into the literature rather then threads here on S.M. where someone mentioned using CaCl2(iirc). Now I have found a paper stating that CaCl2 adsorbs ammonia at room temperature. Good catch, thanks for that :). I'll have to look out for soda-lime(primarily CaOH), but if I can't find it I'll just use NaOH, it's really not that expensive and I have ~400 grams on hand.

Yea I should read some more books, I have only taken gen. chem and currently in org. chem 1. So I'm experimenting a little above my knowledge base. Thanks.





View user's profile View All Posts By User
S.C. Wack
bibliomaster
*****




Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline

Mood: Enhanced

[*] posted on 7-11-2011 at 16:45


Buying soda lime...no that isn't where I was going there.



"You're going to be all right, kid...Everything's under control." Yossarian, to Snowden
View user's profile Visit user's homepage View All Posts By User
smaerd
International Hazard
*****




Posts: 1262
Registered: 23-1-2010
Member Is Offline

Mood: hmm...

[*] posted on 7-11-2011 at 17:05


are you being witty and implying I will be asphyxiated by NH3 fumes and will need a re-breather? hahaha. Do recall in my original post I said this will be done out-side, and on 1 mole scale. I'll be okay :P. I guess experimentation is the best teacher I'll report back some-time tomorrow.



View user's profile View All Posts By User
 Pages:  1  

  Go To Top