simple-guest-7125
Harmless
Posts: 3
Registered: 21-11-2018
Member Is Offline
|
|
Can condensation in a reflux condenser be calculated?
I did a little poking around looking for an answer to this but wasn't finding the right search terms or something.
This is more of a question about selecting the right equipment so I hope someone can help me understand.
I'm not bery knowledgeable about chemistry as far as terminology. I just understand some of the basic concepts. I'm not even sure if the question I
have is very important to know before selecting the best reflux condenser.
What I'm wondering is - If you have say 3 substances that you are going to reflux together call them substance A, substance B, and substance c. How
can it be calculated the length and type of column to use for you rxn?
Thanks.
Attachment: Solvent-Free-Formalin-Free-Eschweiler-Clarke-Methylation-for-Aminese.pdf (137kB)
This file has been downloaded 268 times
|
|
|
DraconicAcid
International Hazard
Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Basically, it depends on the temperature of your cooling water (and the rate of flow), the boiling point of the solvent(s), and how vigorous the
boiling is. I don't see how you would calculate it, but if you see the condensation front near the top of your condensor, run the cold water faster.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
DraconicAcid
International Hazard
Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Volume is also a factor- if I was refluxing 50 mL of dichloromethane, a short column would be sufficient. For 1 L, I'd use a much larger one.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
You can calculate condensation but the visual method is usually more reliable. For a commercial operation, the engineer would calculate it. You need
to know the heat of evaporation, the thermal conductivity of the condenser, the thickness of the condenser and the surface area of the condenser. The
two remaining factors are flow rate and temperature of the cooling fluid. You plug all of that into formulas and you get the maximum amount of
substance condensed.
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Lots of useful info here: http://www.separationprocesses.com/Distillation/MainSet1.htm
|
|
|
simple-guest-7125
Harmless
Posts: 3
Registered: 21-11-2018
Member Is Offline
|
|
Thank you all for so much useful tips and information. Thanks for the link DavidJR. This really helps me understand.
|
|
|
Sulaiman
International Hazard
Posts: 3558
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
On the assumption that your question is equivalent to;
which reflux condenser should I buy ?
I can recommend this cheap but efficient reflux condenser
https://www.ebay.co.uk/itm/200mm-24-29-Glass-Coiled-Reflux-C...
(there are similar available for different neck sizes)
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Tsjerk
International Hazard
Posts: 3022
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
The condenser Sulaiman recommends should be able to condense anything as long as your cooling water is cold enough.
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Yes, I have one of those too and it works pretty well.
You don't want a graham condenser (where the vapour path itself is coiled), you want a coil condenser (where the vapour goes around a coiled tube of
coolant). To make things more confusing the Chinese sellers seem to use the terms interchangeably.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
