Pages:
1
2 |
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Stabilization of diethyl ether by the adition of ethanol
Some time ago, I made diethyl ether by the acid ether synthesis. It worked all right and I stored the final product in a corcked glass bottle in a
fridge over potassium hydroxide.
As the days passed, the potassium hydroxide started precipitating a very flufy white powder out of the ether. At first I thought that those where
impurities in my ether that I wasn't able to remove, so I tested for dissolved peroxides, which yielded a negative result and then I distilled it and
stored it over potassium hydroxide again with the same bottle.
After a couple of days I started seeing the white fluffy precipitate contaminating my ether again, so that leads me to beieve that the precipitate is
actualy ether peroxide being precipitated by the potassium hydroxide.
This would be good if the precipitate didn't stay in suspension. Since I don't want my ether to be contaminated with junk I am looking for ways to
stabilize it. I don't have any BHT so I cannot use it. On further research I found that ether is often sold with 1% ethanol by volume for
non-analytical pruposes, but I couldn't find how this is supposed to inhibit the formation of peroxides.
I also found that copper metal reduces the peroxides to form CuI/CuII.
Would storing my ether over copper wire and adding to it 1% ethanol solve the problem?
Does anyone know the mechanism in which ethanol is supposed to inhibit the formation of peroxides?
I already know there are many other threads on the stabilization of ether but no one talks about doing it with ethanol.
Any answers are apreciated as I dont want my "lab" to explode.
[Edited on 22-2-2019 by Felab]
|
|
arkoma
Redneck Overlord
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
I also am interested to the answer to this question. I distilled enough to COMPLETELY fill my storage bottle to keep out air
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Ether stabilisation experiment
Since no one seems to give an answer, I will conduct an experiment by myself:
-I have taken 10 mls of untreated ether which yielded negative for peroxide formation (as a control) and I bottled it in a 100 ml ground glass flask
(to have planty of air).
I did the same in another flask but ading 200ul of absolute ethanol to the ether.
I will left them for one week in my fridge and then test for peroxides.
Hopefully my house will not explode in the process.
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
I think put it under room temp can speed things up.
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
If peroxides form that fast, I've certainly been taking chances without knowing it.
I always make it fresh in small batches, but I sometimes keep it around for a week or even two.
I thought they formed more slowly than that.
Is there any chance that precipitate is just Koh coming out of solution from the equilibrium conditions?
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Quote: Originally posted by SWIM | If peroxides form that fast, I've certainly been taking chances without knowing it.
I always make it fresh in small batches, but I sometimes keep it around for a week or even two.
I thought they formed more slowly than that.
Is there any chance that precipitate is just Koh coming out of solution from the equilibrium conditions?
|
The thing is that the precipitate looks very yellow and nasty, so I don't think it is.
I also thinked that they formed more slowly and that is why I distilled the ether without looking how to stabilise it.
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
It can also cause my ether to evaporate and create pressure in the container.
Also, the point of the expeiment is testing the formation of peroxides in the conditions I will store it in.
|
|
Alucard
Harmless
Posts: 22
Registered: 6-2-2019
Location: European Union
Member Is Offline
|
|
Quote: Originally posted by Felab | Since no one seems to give an answer, I will conduct an experiment by myself:
-I have taken 10 mls of untreated ether which yielded negative for peroxide formation (as a control) and I bottled it in a 100 ml ground glass flask
(to have planty of air).
I did the same in another flask but ading 200ul of absolute ethanol to the ether.
I will left them for one week in my fridge and then test for peroxides.
Hopefully my house will not explode in the process. |
Diethyl ether is not a chloroform to be stabilized with 1% of ethanol addition, and I have never seen any suggestion like that before, so I doubt
ethanol will work with diethyl ether, I think it only works with chloroform.
Despite I can't give any reference about my source, but I was read about that it's possible to store diethyl ether over a copper metal. From other
hand, if you have ever seen a video on Youtube made by NileRed and this video was about how to prepare diethyl ether, and he suggests to store a ether
over KOH or maybe NaOH, but I'm not sure that adding base to ether will really prevent it from peroxide formation.
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Quote: Originally posted by Alucard | Quote: Originally posted by Felab | Since no one seems to give an answer, I will conduct an experiment by myself:
-I have taken 10 mls of untreated ether which yielded negative for peroxide formation (as a control) and I bottled it in a 100 ml ground glass flask
(to have planty of air).
I did the same in another flask but ading 200ul of absolute ethanol to the ether.
I will left them for one week in my fridge and then test for peroxides.
Hopefully my house will not explode in the process. |
Diethyl ether is not a chloroform to be stabilized with 1% of ethanol addition, and I have never seen any suggestion like that before, so I doubt
ethanol will work with diethyl ether, I think it only works with chloroform.
Despite I can't give any reference about my source, but I was read about that it's possible to store diethyl ether over a copper metal. From other
hand, if you have ever seen a video on Youtube made by NileRed and this video was about how to prepare diethyl ether, and he suggests to store a ether
over KOH or maybe NaOH, but I'm not sure that adding base to ether will really prevent it from peroxide formation. |
There is my source: https://www.sigmaaldrich.com/chemistry/solvents/learning-cen...
I did store over koh but the precipitating ether peroxide derivative makes my ether all cloudy and gross.
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Quote: | As the days passed, the potassium hydroxide started precipitating a very flufy white powder out of the ether. |
That is an assumption
I'm pretty sceptical towards your claim this precipitate being peroxide. Especially when your ether turns out negative when testing for it. I guess it
is KOH.
Also I never heard about ether forming peroxides in days in a fridge, also not in days at any other temperature. It forms in many months, when not
stabilized when plenty of oxygen is present.
KOH is slightly soluble in ether. I can imaging KOH precipitating out as a fluffy white haze, as suggested above.
Was your KOH anhydrous? Usually it is 15% water, 85% KOH, while being stated to be 99+% pure. The KOH part is 99+% in that case, not the whole thing.
KOH is only anhydrous if specifically stated, or when you dried it yourself. If it wasn't one of either your KOH is quite useless as drying agent
(that is what you used it for right?).
What do you need it for? How dry do you need it to be? I guess you are not going to do a Grignard when you are talking about adding ethanol. Add some
anhydrous sulfate salt to dry it, distill it from this salt and the KOH, add 1 % ethanol and store it like that, just make sure it is stoppered tight.
No need for refrigeration. -- This way; No dissolved KOH, no peroxide, dry ether. -- Or at least I would do it that way.
I like your experimentation though, well thought of and thorough! But if it turns out negative for peroxides I would just go for the drying,
distillation and storing with ethanol.
[Edited on 26-2-2019 by Tsjerk]
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Quote: |
I'm pretty sceptical towards your claim this precipitate being peroxide. Especially when your ether turns out negative when testing for it. I guess it
is KOH.
|
Of course I might be wrong, but the precipitate is a yellowish brown when it settles to the bottom so either my potassium hydroxide is extremely
dirty, my ether is dirty al well and I haven't purified it enough or it is the peroxide being precipitated out of solution.
I want to use it in wet plate photography, to make the collodion. For that application ethanol isn't a problem since I will need to ad more later. But
I do need it to be extremely pure as any impurities might ruin the photographs
My koh isn't anhydrous and I dont care for water contamination all that much. Although prior to distilling it I did dry the ether in CaO to make it
clear. I want it since it was supposed to inhibit the formation of peroxides, but it doesn't inhibit their formation, it destroys them contaminating
my ether in the process.
Also, I can't store it non-refrigerated since temperatures in my "lab" can reach 40º celsius or more during summer. Spain is unfortunatley hot.
[Edited on 26-2-2019 by Felab]
|
|
Alucard
Harmless
Posts: 22
Registered: 6-2-2019
Location: European Union
Member Is Offline
|
|
Quote: Originally posted by Felab | Quote: |
I'm pretty sceptical towards your claim this precipitate being peroxide. Especially when your ether turns out negative when testing for it. I guess it
is KOH.
|
Of course I might be wrong, but the precipitate is a yellowish brown when it settles to the bottom so either my potassium hydroxide is extremely
dirty, my ether is dirty al well and I haven't purified it enough or it is the peroxide being precipitated out of solution.
I want to use it in wet plate photography, to make the collodion. For that application ethanol isn't a problem since I will need to ad more later. But
I do need it to be extremely pure as any impurities might ruin the photographs
My koh isn't anhydrous and I dont care for water contamination all that much. Although prior to distilling it I did dry the ether in CaO to make it
clear. I want it since it was supposed to inhibit the formation of peroxides, but it doesn't inhibit their formation, it destroys them contaminating
my ether in the process.
Also, I can't store it non-refrigerated since temperatures in my "lab" can reach 40º celsius or more during summer. Spain is unfortunatley hot.
[Edited on 26-2-2019 by Felab] |
Although ethanol may turn yellowish when treated with strong enough base like KOH, NaOH and even Ca(OH)2, diethyl ether must not turn yellow after
being treated with KOH within at least 24 hours, while this test is performed in a bottle with ether that must be stored in a dark place only, and
only bottle equipped with a glass stopper cork is valid to perform such test. Failing to perform this test means that at least aldehyde or H2O2 are
present along with ether.
To detect peroxides it is possible to perform a test with potassium iodide solution in water, so one could yield such a reaction :
C2H5OOC2H5 + 2KI + H2O = I2 + C2H5OC2H5 + 2KOH
If any peroxides are present with ether, free iodine will be evolved after performing a test described above, turning an ether to yellow color as
well, but adding starch will turn ether into blue color.
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Since a picture is worth a thousand words I will post an image on how I store my ether:
The bottle has frost covering it since it came right out of the fridge, but you can still appreciate the yellow colour of the KOH and the haziness of
the precipitate.
BTW I dont have the ether in an amber bottle since I store it in the fridge and no light can reach it.
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Quote: Originally posted by Alucard |
Although ethanol may turn yellowish when treated with strong enough base like KOH, NaOH and even Ca(OH)2, diethyl ether must not turn yellow after
being treated with KOH within at least 24 hours
|
Guess what this ether was made with?
No, it doesn't. It could also show the presence of ethanol, hydroxide and oxygen.
[Edited on 26-2-2019 by Tsjerk]
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Quote: Originally posted by Alucard | Quote: Originally posted by Felab | Quote: |
I'm pretty sceptical towards your claim this precipitate being peroxide. Especially when your ether turns out negative when testing for it. I guess it
is KOH.
|
Of course I might be wrong, but the precipitate is a yellowish brown when it settles to the bottom so either my potassium hydroxide is extremely
dirty, my ether is dirty al well and I haven't purified it enough or it is the peroxide being precipitated out of solution.
I want to use it in wet plate photography, to make the collodion. For that application ethanol isn't a problem since I will need to ad more later. But
I do need it to be extremely pure as any impurities might ruin the photographs
My koh isn't anhydrous and I dont care for water contamination all that much. Although prior to distilling it I did dry the ether in CaO to make it
clear. I want it since it was supposed to inhibit the formation of peroxides, but it doesn't inhibit their formation, it destroys them contaminating
my ether in the process.
Also, I can't store it non-refrigerated since temperatures in my "lab" can reach 40º celsius or more during summer. Spain is unfortunatley hot.
[Edited on 26-2-2019 by Felab] |
Although ethanol may turn yellowish when treated with strong enough base like KOH, NaOH and even Ca(OH)2, diethyl ether must not turn yellow after
being treated with KOH within at least 24 hours, while this test is performed in a bottle with ether that must be stored in a dark place only, and
only bottle equipped with a glass stopper cork is valid to perform such test. Failing to perform this test means that at least aldehyde or H2O2 are
present along with ether.
To detect peroxides it is possible to perform a test with potassium iodide solution in water, so one could yield such a reaction :
C2H5OOC2H5 + 2KI + H2O = I2 + C2H5OC2H5 + 2KOH
If any peroxides are present with ether, free iodine will be evolved after performing a test described above, turning an ether to yellow color as
well, but adding starch will turn ether into blue color. |
Acetaldehyde is a notoriously difficult to remove contamination in ether made by the acid ether synth so maybe that is causing the yellow precipitate.
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Would acetaldehyde be a problem for your purposed use?
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
As long as it is in a reasonably low concentration it shouldn't be a problem, but the solids evolved by its decomposition in KOH are.
So no more KOH for storing my ether and repace it with copper metal.
The most harmfull impurities are inorganic salts disolved in the ether ( specialy iron salts)
|
|
Alucard
Harmless
Posts: 22
Registered: 6-2-2019
Location: European Union
Member Is Offline
|
|
It ain't pure enough, of course.
Quote: Originally posted by Tsjerk |
No, it doesn't. It could also show the presence of ethanol, hydroxide and oxygen.
[Edited on 26-2-2019 by Tsjerk] |
I agree, it discovers many impurities, not solely aldehyde.
Quote: Originally posted by Felab |
Acetaldehyde is a notoriously difficult to remove contamination in ether made by the acid ether synth so maybe that is causing the yellow precipitate.
|
Perhaps here is an option to try to drain off KOH and then treat ether residue with 5% w/w FeSO4 water solution to remove any present peroxides, then
perform a distillation. It must be enough just about 100 ml of FeSO4 solution per 1 liter of an ether. FeSO4 solution must be slightly acidified with
H2SO4 as well, but only slightly acidified.
You can also oxidize aldehyde to acetic acid with 0,5% w/w KMnO4 water solution. After doing that it's required to wash an ether with 5% w/w NaOH
water solution, and then with water.
[Edited on 26-2-2019 by Alucard]
[Edited on 26-2-2019 by Alucard]
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Quote: Originally posted by Felab |
So no more KOH for storing my ether and repace it with copper metal.
The most harmfull impurities are inorganic salts disolved in the ether ( specialy iron salts) |
Copper isn't needed as long as you add ethanol. I wouldn't use it when metal salts are your enemy.
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Or the fluffy stuff is potassium ethoxide...
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Maybe but I fractionated the ether at exactly 34.6 Cº so ethanol contamination is unikely. I also mixed it with CaCl2 before distilling it.
|
|
Tsjerk
International Hazard
Posts: 3030
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I'm looking forward to the results of your week long experiment, I'm getting curious now.
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
BTW ethanol will stop turning color with base forever after enough refluxing with it. Perhaps the same can happen here. Ether for lab use at least
through the 70's was often old stock of Squibb medical ether, with copper plated to the inside of the can. The cans did come with a cork but I don't
think long term storage of opened cans was really the plan. This ether had been pretreated with copper, producing oxygen or CO2, surface oxide, and
acid then removed with wet magnesium hydroxide. Perhaps you're getting acetate. It would be interesting to compare with the anhydrous NaOH.
[Edited on 27-2-2019 by S.C. Wack]
|
|
Felab
Hazard to Self
Posts: 76
Registered: 9-11-2018
Member Is Offline
Mood: :dooM
|
|
Experiment delay...
When I went this morning to check on the experiment the stopper had blown up as I didn't use a keck clip, and the ether had evaporated all too.
I replaced the contents of the flask and puted on some keck clips. The results may be delayed for two days.
Apologies.
[Edited on 28-2-2019 by Felab]
|
|
woelen
Super Administrator
Posts: 8009
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Storing ether in a bottle with a cork does not sound good to me. Corks are somewhat porous and ether certainly will escape through that.
Best is to store the ether in a glass bottle having a cap with Al-foil liner. You can buy bottles with such caps, but you can also make one yourself
easily from folded household foil and a decent cap with a flat foam liner. I myself store my ether in such a bottle and even after years of storage I
do not notice any relevant loss of ether.
Diethyl ether can be stabilized for peroxide formation with tiny amounts of BHT or benzophenone (a few tens of ppm or so). Benzophenone is not that
hard to obtain, BHT may be somewhat harder to obtain.
I have doubts about storing ether with KOH or NaOH. Does this really prevent formation of peroxides? Why don't others store ether over these?
The brown crap you see most likely is due to impurities in your ether. I think that there are organic impurities, which with KOH (and possibly some
water from the 85% KOH) condenses into larger polymeric species. Such stuff is very common in organics and usually it is yellow/brown at very low
concentration, reddish/brown in small amounts and brown/black in larger concentrations. Especially aldehydes, ketones and unsaturated C=C bonds tend
to form such condensed species.
|
|
Pages:
1
2 |