jwrigly
Harmless
Posts: 1
Registered: 7-8-2019
Member Is Offline
|
|
Sintered Funnel Clogged with Cr2O3
I've managed to clog one of my sintered funnels with Chromium Oxide. I've tried putting conc NaOH and conc HNO3 through it but there was no change. Is
it possible to dissolve Cr2O3, or convert it into something soluble?
I've read that it should react with conc acid/alkali to produce complex ions. Does the acid / base need to be heated? Or is it a very slow process?
|
|
ZetekitoxinAB
Harmless
Posts: 19
Registered: 31-7-2019
Member Is Offline
Mood: Omberacetam
|
|
Maybe try adding dropwise conc NaOH and 30% H2O2 alternately ? Perhaps the energetic decomposition of the hydrogen peroxide would help cleaning out
the particles and maybe also convert Cr2O3 into soluble chromate. It might damage the funnel though, I am not sure.
|
|
TheMrbunGee
Hazard to Others
Posts: 364
Registered: 13-7-2016
Location: EU
Member Is Offline
Mood: Phosphorising
|
|
Quote: Originally posted by ZetekitoxinAB | Maybe try adding dropwise conc NaOH and 30% H2O2 alternately ? Perhaps the energetic decomposition of the hydrogen peroxide would help cleaning out
the particles and maybe also convert Cr2O3 into soluble chromate. It might damage the funnel though, I am not sure. |
Looks like jwrigly does not have H2O2.
Try pushing water or soap water trough the filter form bottom, that may release some particles stuck.
Then you may leave some alkali solution to sit for few days in the funnel, maybe gravity drip alkali solution trough. Remember, that strong alkali
solutions might damage the sintered glass. You may increase the concentration following formula:
(alkali concentration = willingness to have a clean nice filter - possibility to buy new one - financial status)
Leave it for few days. You might never have a nice clean filter again, but from another perspective - it is just metal oxide, not carbon (in my case)
Good luck!
[Edited on 7-8-2019 by TheMrbunGee]
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Soaking in warm solution is the trick to allot of such issues.
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
I'd try EDTA.
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
The problem is not so such on dissolving the Cr2O3, but on what to do responsibly with the toxic waste produced in the process. Either strong H2O2 or
HOCl (from like vinegar + Chlorine Bleach) should work with time.
See my comments and sources together with all WARNINGS in this prior SM thread https://www.sciencemadness.org/whisper/viewthread.php?tid=18... .
|
|
unionised
International Hazard
Posts: 5119
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Convert it back to Cr2O3
|
|
woelen
Super Administrator
Posts: 8006
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
What might help is slowly pouring a hot alkaline solution of NaBrO3 or KBrO3 through the funnel. Maybe it also works with conc. NaOCl, to which
additional NaOH is added.
As others already pointed out, strong alkalies may damage the sintered glass somewhat.
After this treatment it is very important to rinse with distilled water in order to remove any leftover alkali.
If after this treatment some Cr2O3 remains behind, then you can simply use it with that material trapped in it. Cr2O3 is nearly as inert as the funnel
itself and if it is trapped, then it will not contaminate anything which you pour through it.
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
Glass is much more soluble in alkali than Cr2O3. I have mentioned that KMnO4 with conc. sulfuric acid/drain cleaner dissolves/+6's even the most dead
burnt pigment, and sometimes "MnO2" will as well, but AFAIK no one has monetized this information with video or prepchem, so it must not exist.
|
|