Petn1933
Hazard to Others
Posts: 106
Registered: 16-9-2019
Member Is Offline
|
|
Electric initiator
Hello
I want to know from your experience what kind of wire you are using in head of electric initiator to create heat?
I use 3v lamp element
Tnx
|
|
|
johnmay
Harmless
Posts: 9
Registered: 7-1-2019
Member Is Offline
|
|
Hello there,
Personally I use short fragments of metal scourer (the thing that you use to clean after the dinner if you are lame at cooking  )
I cut it in about 2 cm pieces and twist between the two wires.
It goes red hot even when using regular AA batteries.
Best regards!
|
|
|
underground
National Hazard
Posts: 692
Registered: 10-10-2013
Location: Europe
Member Is Offline
|
|
I personally use Nichrome wire, 40 AWG.
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
I used to clip the tips off christmas lights. These days, it's easier just to buy electric matches for fireworks from eBay. They're only around 20
cents each if you buy a pack of 100 and it saves a lot of time and effort, and they're far more reliable, especially if you gang 2 or 3 together for
redundancy.
https://www.ebay.com/itm/100pcs-lot-11-81in-Fireworks-Wire-F...
|
|
|
Petn1933
Hazard to Others
Posts: 106
Registered: 16-9-2019
Member Is Offline
|
|
Thanks for all your comments
All of this are great
Steel wool and nichrome wire are inexpensive
Online E matches more reliable
i will test them !
[Edited on 27-9-2019 by Petn1933]
|
|
|
Vomaturge
Hazard to Others
Posts: 285
Registered: 21-1-2018
Member Is Offline
Mood: thermodynamic
|
|
I've ignited a ground up match head with a christmas light. I wasn't trying light anything else with it, though. Sometimes, we do things just to see
if it's possible. The beauty of it is that the filament can light without much power. The sad part is that if you poke a whole match, or a fuse, or
any number of other things in, you will break it and have a dud.
For an experiment with lighting candles and toothpicks in closed container, I used a twist tie which was maybe .5 mm thick. In order to get it to melt
and ignite flames instead of just charring the fuel, I used a 50A 12V car jump starter and fed it with 2ft 16AWG copper wires. If you're trying to
electrically ignite something which won't light easily and won't be too violent (so you don't damage the jump starter), I think this method is hard to
beat.
Random thought 1: I should try that experiment again, with some minor changes. Last time, I never figured out what steady state burning of a candle
would look like at 7x atmospheric pressure.
Random thought 2: a Yablochkov candle just might make a nice ignitor for a stubborn reaction like thermite. Just saying...
[Edited on 28-9-2019 by Vomaturge]
|
|
|
wg48temp9
National Hazard
Posts: 761
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
My thought is such a candle could be used in an arc furnace so that the need to adjust the carbon rods as they burn away would not be needed.
For example in making CS2, P or Na. Perhaps with the calcium sulphate replaced with a different material more compatible with the intended reaction.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1636
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
I use Nichrome doped with lead styphnate and Nitro cellulose.
Going to make a spot welding rig for welding the bridge wire, I have all so used steel wool strands soldered on, but much more delicate to apply
doping mixture to some times.
|
|
|
underground
National Hazard
Posts: 692
Registered: 10-10-2013
Location: Europe
Member Is Offline
|
|
Does it go bang just like that ? Could a SADA work as a replacement of LS ?
|
|
|
XeonTheMGPony
International Hazard
Posts: 1636
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
it fires with a very solid crack
My preferred doping method is to have a thin gel, dip assembly in that, then dust with priming agent, then dip in a thicker gel to coat the priming
compound. this protects every thing from moisture, air, movement. Makes for a very sturdy and reliable E-match.
  
[Edited on 28-9-2019 by XeonTheMGPony]
|
|
|
underground
National Hazard
Posts: 692
Registered: 10-10-2013
Location: Europe
Member Is Offline
|
|
Very clever idea thanks. I have never considered an e-mach detonator. I bet SADA will work too
|
|
|
XeonTheMGPony
International Hazard
Posts: 1636
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
I was never a fan of fuses for the most part, so all ways preferred electrical, so much more reliable and safer.
 
|
|
|
dave321
Harmless
Posts: 45
Registered: 22-11-2012
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by XeonTheMGPony  | I use Nichrome doped with lead styphnate and Nitro cellulose.
Going to make a spot welding rig for welding the bridge wire, I have all so used steel wool strands soldered on, but much more delicate to apply
doping mixture to some times. |
be interested if you get your welding rig sorted, please provide details when ready
[Edited on 29-9-2019 by dave321]
|
|
|
sodium_stearate
Hazard to Others
Posts: 255
Registered: 22-4-2011
Location: guard duty at the checkpoint
Member Is Offline
Mood: No mask.
|
|
Estes rockets
When I was a kid I had Estes model rockets.
At one time most hobby stores sold lengths of nichrome
wire to be used as electric heaters to start the Estes
rocket engines.
As I recall, it was probably about #30 Ga. wire.
You'd cut a short length of it, maybe 1.5 inches long,
then wind it in a few turns around the sharp end of a pencil
lead. That would leave a little coil with leads sticking out
from both ends.
You'd then push this tiny coil up into the rocket engine
nozzle, and secure it in there by pushing a small piece
of wadded up kleenex or tissue paper in behind it.
The two short wire leads then were attached via two
small clips to the launch circuit, which was nothing more
than a plain 6 volt lantern battery and a push button
on a long 2 conductor lamp cord.
After a few years all the hobby stores discontinued the
sale of the nichrome wire. Estes instead started manufacturing
special little assemblies that had the pre-made little
coil, but it was coated with some compound resembling
that of a match head. Those worked too.
"Opportunity is missed by most people
because it is dressed in overalls and it
looks like work" T.A. Edison
|
|
|
MineMan
National Hazard
Posts: 998
Registered: 29-3-2015
Member Is Offline
Mood: No Mood
|
|
Buy the firework ones on eBay. Nothing worse than a dud. Especially when it’s not just the cap.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
