Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: DCM
Housane
Hazard to Others
***




Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline

Mood: Let’s make

[*] posted on 22-1-2020 at 13:44
DCM


Hi I am wondering if ethyl acetate could be used as a direct DCM replacement as DCM becomes increasingly hard to find for extractions like caffeine from tea.

Housane




Green QD's so far

Feel free to correct grammar or incorect knknowledge. We are all learning.
View user's profile View All Posts By User
DavidJR
National Hazard
****




Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline

Mood: Tired

[*] posted on 22-1-2020 at 13:51


This is too vague to answer. It will probably be suitable for some uses but not for others. So no, it is not a "direct replacement", but for extracting caffeine from tea, it might well work.
View user's profile View All Posts By User
Housane
Hazard to Others
***




Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline

Mood: Let’s make

[*] posted on 22-1-2020 at 14:03


Ok, for extractions like caffeine and others with a DCM solvent would normally be possible with ethyl acetate



Green QD's so far

Feel free to correct grammar or incorect knknowledge. We are all learning.
View user's profile View All Posts By User
Steam
Hazard to Others
***




Posts: 238
Registered: 25-3-2014
Location: Minnesota
Member Is Offline

Mood: Triple Point

[*] posted on 22-1-2020 at 18:27


One of the main issues with EtAc is that it can degrade into ethanol and acetic acid under certain conditions. As long as you avoid those conditions and trace amounts of ethanol and Ac acid are not detrimental then you should be good to go. If you think DCM is hard to find, try getting a hold of carbon tetrachloride via OTC sources.... :d



DISCLAIMER: The information in this post is provided for general informational purposes only and may not reflect the current law in your jurisdiction. No information contained in this post should be construed as legal advice from the individual author, nor is it intended to be a substitute for legal counsel on any subject matter. No reader of this post should act or refrain from acting on the basis of any information included in, or accessible through, this post without seeking the appropriate legal or other professional advice on the particular facts and circumstances at issue from a lawyer licensed in the recipient’s state, country or other appropriate licensing jurisdiction.
View user's profile Visit user's homepage View All Posts By User
Housane
Hazard to Others
***




Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline

Mood: Let’s make

[*] posted on 22-1-2020 at 23:05


Quote: Originally posted by Steam  
One of the main issues with EtAc is that it can degrade into ethanol and acetic acid under certain conditions. As long as you avoid those conditions and trace amounts of ethanol and Ac acid are not detrimental then you should be good to go.


What conditions do I need to avoid is it alklinity, acidity or heat





Green QD's so far

Feel free to correct grammar or incorect knknowledge. We are all learning.
View user's profile View All Posts By User
Tsjerk
International Hazard
*****




Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline

Mood: Mood

[*] posted on 23-1-2020 at 03:01


Quote: Originally posted by Housane  


What conditions do I need to avoid is it alklinity, acidity or heat



Acid in combination with water and alklinity in general. Heat is no problem in normal extractions, the solvent just boils off.

Just realize ethyl acetate dissolves a lot of water (3%) that has to be taken care of before you evaporate it to isolate your product. Also ethyl acetate is pretty soluble in water (8%).

Always make sure you use saturated NaCl instead of plain water when working with ethyl acetate.

View user's profile View All Posts By User
Housane
Hazard to Others
***




Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline

Mood: Let’s make

[*] posted on 23-1-2020 at 12:27


Quote: Originally posted by Tsjerk  
Quote: Originally posted by Housane  


What conditions do I need to avoid is it alklinity, acidity or heat



Acid in combination with water and alklinity in general. Heat is no problem in normal extractions, the solvent just boils off.

Just realize ethyl acetate dissolves a lot of water (3%) that has to be taken care of before you evaporate it to isolate your product. Also ethyl acetate is pretty soluble in water (8%).

Always make sure you use saturated NaCl instead of plain water when working with ethyl acetate.



Thanks that is very helpful




Green QD's so far

Feel free to correct grammar or incorect knknowledge. We are all learning.
View user's profile View All Posts By User
happyfooddance
National Hazard
****




Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline

Mood: No Mood

[*] posted on 23-1-2020 at 15:29


Ethyl acetate is used to decaffeinate coffee industrially, so yes.

However, caffeine is much more soluble in DCM and chloroform, so these will be much better for caffeine extraction in the lab.

Chloroform can be easily made from acetone and bleach, or isopropanol and bleach, via haloform reaction.
View user's profile View All Posts By User
Texium
Administrator
********




Posts: 4606
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline

Mood: PhD candidate!

[*] posted on 23-1-2020 at 20:25


For extractions, ethyl acetate is generally a suitable replacement (as long as significant acidity or alkalinity are avoided, as noted by previous posters). The only other issue with it in that application is that since it's less dense than water, performing multiple extractions is a bit more cumbersome than it is with DCM.

Things get more complicated if you want to make the swap for use in chromatography. For normal phase chromatography, ethyl acetate is a much more potent eluent than DCM. In my experience, eluting a compound with 1% of ethyl acetate in hexanes or petroleum ether will give similar results to eluting with 10% DCM in hexanes or petroleum ether. Therefore, if you were following a procedure where DCM/hexanes is used for a column, you would want to reduce the percentage tenfold to use ethyl acetate in its place, and it may not go as smoothly if it's super non-polar compounds that you're trying to separate.




Come check out the Official Sciencemadness Wiki
They're not really active right now, but here's my YouTube channel and my blog.
View user's profile Visit user's homepage View All Posts By User

  Go To Top