9CWAI
Harmless
Posts: 16
Registered: 5-2-2019
Location: Utah
Member Is Offline
|
|
How do I make Lactic Acid from Polylactic Acid?
I have lots of PLA waste from a 3d printer and no hotplate so I cannot temperature control enough to not burn it when melting it. I want to make
Lactic acid from it but boiling for a while did little but warp it. How can I encourage the water to attack the PLA?
|
|
DraconicAcid
International Hazard
   
Posts: 4393
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
You should be able to hydrolyze it with strong base to get lactate ion, then acidify to get lactic acid.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
SaccharinSlayer157
Harmless
Posts: 28
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
Well, I was going to say something about that but apparently I'm wrong, so nevermind 
[Edited on 9-1-2022 by SaccharinSlayer157]
|
|
9CWAI
Harmless
Posts: 16
Registered: 5-2-2019
Location: Utah
Member Is Offline
|
|
What would you recommend out of the easily obtainable 3, Ca(OH)2, NaOH, or KOH? which one would be the easiest to get rid of?
|
|
9CWAI
Harmless
Posts: 16
Registered: 5-2-2019
Location: Utah
Member Is Offline
|
|
I really don't wanna use H2SO4.
|
|
DraconicAcid
International Hazard
   
Posts: 4393
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
If you use calcium hydroxide, then you can neutralize with sulphuric or phosphoric acid, filter out the calcium salts, and have a fairly pure solution
of lactic acid. If you acidify with a different acid (such as hydrochloric), then regardless of which base you use, you'll want to have an excess of
base so that you can distill the lactic acid (ew!) without any excess acid coming over.
Just hypothesizing here, but you might also be able to hydrolyze the polymer by refluxing it in aqueous acid for a while, adding just enough
bicarbonate to neutralize the acid that you've added, and then distilling.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
9CWAI
Harmless
Posts: 16
Registered: 5-2-2019
Location: Utah
Member Is Offline
|
|
Quote: Originally posted by DraconicAcid  | If you use calcium hydroxide, then you can neutralize with sulphuric or phosphoric acid, filter out the calcium salts, and have a fairly pure solution
of lactic acid. If you acidify with a different acid (such as hydrochloric), then regardless of which base you use, you'll want to have an excess of
base so that you can distill the lactic acid (ew!) without any excess acid coming over.
Just hypothesizing here, but you might also be able to hydrolyze the polymer by refluxing it in aqueous acid for a while, adding just enough
bicarbonate to neutralize the acid that you've added, and then distilling. |
Yeah, I did the math and sulfuric is the best option unfortunately. Even compared to buying lactic acid. 24 a gallon and a half at Home Depot, the PLA
is waste anyway, and eggshells are a fine source of calcium. less than a cent per gram if I do it that way rather than like a dollar per gram on eBay.
|
|