| Pages:
1
2 |
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
Phenol from Domestically Available Chemicals
I have not yet had a chance to try this synthesis, but I have come up with the procedure. Start by reacting a quantity of aspirin (acetylsalicylic
acid) with saturated aqueous sodium hydroxide solution (crystal drain opener) until it is all dissolved. The aspirin may contain binders that do not
dissolve, so simply filter the solution. The solution will consist of sodium salicylate and sodium acetate. Now, slowly add concentrated hydrochloric
acid (hardware store muriatic acid) in small amounts. Keep adding HCl until no more salicylic acid precipitates out. Acetic acid will have formed as a
byproduct, but it will stay in solution. Filter out the salicylic acid, wash it with water, and set it aside to dry.
Once the salicylic acid is dry, put 25g of it into a suitable round-bottom flask and clamp the flask to a ring stand. Now, heat the salicylic acid
with a hot torch for 5-6 seconds at a time, pausing 10-15 seconds between heating sessions. Continue to heat and pause for a total of 10-15 minutes.
During the heating, the salicylic acid will break down into phenol and carbon dioxide gas. After heating, allow the flask to cool to room temperature,
and add 100ml of dichloromethane (distilled from paint stripper). Swirl the flask until all of the phenol is dissolved. Now set up for distillation
and distill off the dichloromethane at 40 degrees Celsius. When all of the dichloromethane is removed, the residue in the boiling flask will be
composed of phenol with a purity of 95 to 98%.
[Edited on 8-4-2013 by ParadoxChem126]
[Edited on 8-4-2013 by ParadoxChem126]
[Edited on 8-4-2013 by ParadoxChem126]
[Edited on 8-4-2013 by ParadoxChem126]
[Edited on 9-4-2013 by ParadoxChem126]
|
|
|
Nicodem
|
Thread Moved
8-4-2013 at 11:34 |
vmelkon
National Hazard
Posts: 669
Registered: 25-11-2011
Location: Canada
Member Is Offline
Mood: autoerotic asphyxiation
|
|
I think you could do a decarboxylation reaction with the salicyclic acid.
Heat solid salicyclic acid with solid NaOH to 500 °C or something like that. You should end with phenol and Na2CO3.
|
|
|
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
Well, if you heat the molten phenol to 500 degrees Celsius, won't it all instantly vaporize? Also, I would not want to mess with molten sodium
hydroxide and phenol vapors...
|
|
|
Finnnicus
Hazard to Others
Posts: 342
Registered: 22-3-2013
Member Is Offline
|
|
[Edited on 9-4-2013 by Finnnicus]
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Certain throat sprays also contain phenol.
It might make an interesting work-up to isolate the phenol.
Chloraseptic
|
|
|
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
Yeah, but the ingredients list phenol as 1.4%. You would only be able to isolate a very small amount from the entire bottle. Still might be
interesting to try…
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Quote: Originally posted by vmelkon  | I think you could do a decarboxylation reaction with the salicyclic acid.
Heat solid salicyclic acid with solid NaOH to 500 °C or something like that. You should end with phenol and Na2CO3. |
I hope you have a steel container for that molten NaOH.
Isn't phenol deathly toxic?
I hope that decomposition of salicylic acid works - I'd love a good source of phenolphthalein.
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
| Quote: Originally posted by ParadoxChem126 | | Yeah, but the ingredients list phenol as 1.4%. You would only be able to isolate a very small amount from the entire bottle. Still might be
interesting to try… |
That comes to about 2.4g per bottle.
If you want cheap go the benzene sulfonate route or cumene hydroperoxide method.
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
In large quantities, breathing hot phenol gas or getting hot phenol on your skin is inadvisable. Of course the same can be said for steam and boiling
water. It is somewhat toxic but certainly not as toxic as hydrochloric acid. If exposed to vapor, seek medical attention. If you get it on your
skin wash it off and seek medical attention if there is skin damage. If it is hot and you get it on your skin, it will cause severe burns. Small
quantities are used as a throat medication, so I wouldn't freak out if I got a speck of dust on my arm. Of course, if you get a little sulphuric acid
on your arm it will leave a mark.
|
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by macckone |
In large quantities, breathing hot phenol gas or getting hot phenol on your skin is inadvisable. Of course the same can be said for steam and boiling
water. It is somewhat toxic but certainly not as toxic as hydrochloric acid. If exposed to vapor, seek medical attention. If you get it on your
skin wash it off and seek medical attention if there is skin damage. If it is hot and you get it on your skin, it will cause severe burns. Small
quantities are used as a throat medication, so I wouldn't freak out if I got a speck of dust on my arm. Of course, if you get a little sulphuric acid
on your arm it will leave a mark. |
Actually a speck of phenol on your arm it is absorbed and will cause burns and blistering. It is quite toxic actually. More so than HCl...
|
|
|
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by elementcollector1 | | Quote: Originally posted by vmelkon | I think you could do a decarboxylation reaction with the salicyclic acid.
Heat solid salicyclic acid with solid NaOH to 500 °C or something like that. You should end with phenol and Na2CO3. |
I hope you have a steel container for that molten NaOH.
Isn't phenol deathly toxic?
I hope that decomposition of salicylic acid works - I'd love a good source of phenolphthalein. |
The decomposition of salicylic acid should work... Check out this website about phenol from salicylic acid.
http://books.google.com/books?id=y5mZrW1KB_AC&pg=PA129&a...
|
|
|
zed
International Hazard
Posts: 2277
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
http://www.youtube.com/watch?v=hlR3UWLyxEU
Don't know how difficult these chemicals are to acquire. But, in my day if you needed Phenol you either bought it outright, or made it from Aniline.
Or, if you were a Chem student, you Nitrated Benzene, Reduced the Nitrobenzene it to Aniline.....Etc.
Aspirin seems like an interesting alternative.
|
|
|
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
Benzene and nitric acid are not easily accessible to me, so I've kind of ruled out the aniline approach. Also, I don't have a fume hood, and I don't
want to mess with benzene without one.
|
|
|
chemcam
Hazard to Others
Posts: 423
Registered: 18-2-2013
Location: Atlantis
Member Is Offline
Mood: I will be gone until mid-september, on a work contract.
|
|
I can verify that the OP's procedure works, at least sort of, I have done it personally a while back with 2 failures and 1 success. I believe the
failures took place because I do not have a Bunsen burner I was using a propane torch, held at a distance of course, so the heat applied was never
consistent. I used chloroform in the place of DCM. I was thinking about doing a YouTube video since none exist on the topic but I haven't had a chance
to improve the dependability.
|
|
|
ChemistryGhost
Hazard to Others
Posts: 113
Registered: 5-7-2012
Member Is Offline
Mood: Supercooled 
|
|
Maybe you could obtain cumene and try using the cumene process in a Hock rearrangement to obtain acetone and phenol. Acetone is always useful.
"Imagination is more important than knowledge" ~Einstein
|
|
|
zed
International Hazard
Posts: 2277
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Well, Benzene is a carcinogen.......eventually. A few minor exposures are unlikely to give you the big C... Everybody, used to get lots of Benzene
exposure, all of the time. Most of us are just fine.
Aniline can also be prepared by the degradation of Benzamide. A material you could likely produce from Benzoic Acid, or Sodium Benzoate. These are
materials that can be obtained cheaply, and in bulk.
[Edited on 11-4-2013 by zed]
|
|
|
vmelkon
National Hazard
Posts: 669
Registered: 25-11-2011
Location: Canada
Member Is Offline
Mood: autoerotic asphyxiation
|
|
Wow, that is very simple. Just heat the salicyclic acid.
The text suggests to use methylene chloride (DCM, CH2Cl2) which I don't have but I guess other solvents would do the job as well.
In the USA, you can buy BBQ cleaner liquid and distill to get the CH2Cl2 out.
[Edited on 19-4-2013 by vmelkon]
|
|
|
ParadoxChem126
Hazard to Others
Posts: 104
Registered: 5-4-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
I think that distilling it from paint stripper is cheaper.
[Edited on 5-5-2013 by ParadoxChem126]
|
|
|
BlackDragon2712
Hazard to Others
Posts: 124
Registered: 22-12-2012
Location: Everywhere
Member Is Offline
Mood: Sleepy
|
|
Phenol, a quite toxic chemical but damn I love its smell xD!
I can confirm that the decarboxylation of salicylic acid does in fact work. The first minute after you put the flame out a strong smell of phenol is
perceptible. Later I made the extraction using ethyl acetate and apparently it worked just fine. Recristalization was made later using water as the
solvent. You can get very pure fenol from this method (pure enough as to what a home chemist can ask for)
I do apologize for not having any photograph of the other processes; this was actually taken by a friend of mine.
|
|
|
DJF90
International Hazard
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
Theres a fairly detailed experimental over at Versuchschemie
|
|
|
macckone
International Hazard
Posts: 2159
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
| Quote: |
Actually a speck of phenol on your arm it is absorbed and will cause burns and blistering. It is quite toxic actually. More so than HCl...
|
Not true
HCl LD50 oral (human) 2.8mg/Kg
Phenol LD50 oral 270mg/Kg
Phenol is not as toxic as most of the stuff we take for granted.
If it were that toxic it wouldn't be in Chloraseptic.
Having said that, take reasonable precautions because it can be dangerous but then so can potassium chloride.
[Edited on 1-10-2013 by macckone]
|
|
|
MichiganMadScientist
Hazard to Self
Posts: 55
Registered: 22-7-2013
Member Is Offline
Mood: No Mood
|
|
So, is anyone here agreeing with the OP regarding producing the salicylic acid from aspirin tablets? Because honestly, producing phenol from aspirin
tablets sounds way easier than the other methods mentioned here such as trying to screw around with benzene, etc. I understand there might be purity
issues from binders in aspirin tablets, but at that, pure aspirin is itself a fairly simple synth. However, one has to come by acetic anhydride for
that, and thus, simply generating the salicylic acid from aspirin tablets becomes a bit more desirable for me.
Also, the step involving the dichloromethane is simply a recrystallization, correct? One should have crude phenol simply from heating the
salicylic acid, and this crude phenol should be solid once it cools to room temp?
[Edited on 1-10-2013 by MichiganMadScientist]
|
|
|
Random
International Hazard
Posts: 1018
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
I have found one study about chlrobenzoic acid synthesis from hypochlorite and benzoic acid and then probably hydroxybenzoic acids may be obtained
from them with NaOH, they could be used instead of aspirin for decarboxylation.
|
|
|
DJF90
International Hazard
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
@Macckone: Where did you get that data from? Its way off according to Sigma:
HCl (gas) LD50 Oral (Rabbit) 900 mg/kg
Phenol LD50 Oral (Rat) 410-650 mg/kg, LD50 Dermal (Rabbit) 630 mg/kg
Phenol is pretty nasty stuff. Its hepatotoxic (liver) and sufficiently volatile to cause concern. I've seen a bottle where half the contents were in
the upper part of the bottle due to sublimation.
The crude phenol can be (vacuum) distilled to purify to an acceptable level (again, see the VC page).
[Edited on 1-10-2013 by DJF90]
|
|
|
bfesser
Resident Wikipedian
Posts: 2114
Registered: 29-1-2008
Member Is Offline
Mood: No Mood
|
|
Provide the link, then.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
