Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Warning about OTC solvants
trinitrotoluene
Hazard to Others
***




Posts: 142
Registered: 17-10-2002
Location: California
Member Is Offline

Mood: paranoid

[*] posted on 12-8-2004 at 02:07
Warning about OTC solvants


I always suspected that OTC solvants were not really pure. Indeed this was proven true. I was curious about acetone, so I took a quart (946ml)of acetone and did a distillation on it. The brand that was used was Klean Strip brand, purchased from the Home Depo. I proceeded to distill it using a water bath. This was distilled using a 500ml erlinmyers flasks, some Cu tubing and 125ml RB flask at the receiving end. After 4 hours of distilling, I finally distilled off all the acetone, and I was left with 3ml of this yellowish liquid. It was a good idea I used a water bath, it kept the temperature steady, and once all the acetone distilled away, the other gunk dosen't distill over.

But this yellow liquid has a low viscosity like any other solvant, but when I took a smell it smelled nothing like that ketone acetone. It smelled like it was a hydrocarbon, very simular to the smell of gasoline.

I tossed the last 25ml of acetone that had distilled over, I basically used it to clean the tubing.

As of now, I will distill all my OTC solvants to ensure purity, I suspect other OTC solvants are contaminated with other organic impurties as well. If you need high purity solvants I recommend a careful distillation of those chemicals.




TNT
View user's profile View All Posts By User This user has MSN Messenger
vulture
Forum Gatekeeper
*****




Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline

Mood: No Mood

[*] posted on 12-8-2004 at 04:00


DON'T just distill solvents like acetone and ethers like that! There is always some peroxide content in there which stays behind!

The leftover you saw could very well be a mixture of condensation products/peroxides.




One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
View user's profile View All Posts By User
Democritus of Abdera
Harmless
*




Posts: 47
Registered: 5-8-2004
Location: The Prefecture of Abdera in the region of Xanthi.
Member Is Offline

Mood: Stone Dead

[*] posted on 12-8-2004 at 08:42
Yes, there is something else in OTC solvents


I had mentioned it several months ago, in this thread http://www.sciencemadness.org/talk/viewthread.php?tid=1415 Under the username Hermes Trismegistus.

The product you found is a rust-inhibitor, it plagued my younger days when I would use various solvent for the extraction of "herbal" products and made alot of trouble for those of us trying the chlorobutanol synth,

When the acetone/rust inhibitor was oxidized to chloroform, the R.I. must jump right into the chloroform layer, when the acetone/chloroform mixture is reacted to form chlorobutanol, the R.I. must have an affinity for the solid chlorobutanol and lock lips with it.

I found the solution in getting pure and stable white crystals was in pre-distilling both the acetone and chloroform prior to attempting the synth but I'm not certain anyone paid me any mind.

It wouldn't be suprising, because besides being a rank amateur in the chemical arts in comparison to many of the resident illuminati, I'm also very opinionated.

I once argued (very unsuccessfully) with someone on this forum, that the heat capacity of moist air must be significantly different to that of dry air. It turned out I was arguing with a chemical engineer who designed cooling towers for seven years.

Boy, did I feel stupid! Of course being completely wrong never seemed to stop me from getting in an argument though.....:D




Do not meddle in the affairs of wizards, for you are crunchy and taste good with ketchup.\"--- Marcel Marceau
View user's profile Visit user's homepage View All Posts By User
If_6_was_9
Unregistered




Posts: N/A
Registered: N/A
Member Is Offline


[*] posted on 12-8-2004 at 15:29


I've seen something refered to as virgin acetone in stores used for removing finger nail polish. I wonder how pure that is.
If_6_was_9
Unregistered




Posts: N/A
Registered: N/A
Member Is Offline


[*] posted on 12-8-2004 at 15:31


Check this out:

http://www.tapplastics.com/shop/product.php?pid=11

http://www.google.com/search?hl=en&ie=ISO-8859-1&q=v...

[Edited on 12-8-2004 by If_6_was_9]
trinitrotoluene
Hazard to Others
***




Posts: 142
Registered: 17-10-2002
Location: California
Member Is Offline

Mood: paranoid

[*] posted on 12-8-2004 at 21:50


Vulture, people tossed metal into diethyl ether to prevent the formation of peroxides. I did the same when I was distilling acetone by tossing silver into there. And I distilled it carefully in a water bath at 80*C.



TNT
View user's profile View All Posts By User This user has MSN Messenger
Saerynide
National Hazard
****




Posts: 954
Registered: 17-11-2003
Location: The Void
Member Is Offline

Mood: Ionic

[*] posted on 12-8-2004 at 22:48


Why does tossng in metal keep peroxides from forming?



"Microsoft reserves the right at all times to monitor communications on the Service and disclose any information Microsoft deems necessary to... satisfy any applicable law, regulation or legal process"
View user's profile View All Posts By User
kyanite
Hazard to Self
**




Posts: 86
Registered: 30-6-2004
Location: is not important!
Member Is Offline

Mood: lactamic

[*] posted on 13-8-2004 at 04:17


I think it has something to do with breaking down the peroxide bond like using silver in H2O2 engines.
The metal is a catalyst
View user's profile View All Posts By User
vulture
Forum Gatekeeper
*****




Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline

Mood: No Mood

[*] posted on 13-8-2004 at 10:50


Catalysing the decomposition of the peroxides does not seem a very good idea to me, as this would only increase the danger of explosion.

The metal is probably there to reduce the peroxides. This can also be done with FeSO4, Na2S, etc.




One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
View user's profile View All Posts By User
Democritus of Abdera
Harmless
*




Posts: 47
Registered: 5-8-2004
Location: The Prefecture of Abdera in the region of Xanthi.
Member Is Offline

Mood: Stone Dead

[*] posted on 13-8-2004 at 11:03


Quote:
Originally posted by vulture
Catalysing the decomposition of the peroxides does not seem a very good idea to me, as this would only increase the danger of explosion.


If the action was catalysis, would the regular catalysis of single peroxides pose a real threat?
Would it result in a buildup of gas in the container?
Would the gas layer over the solvent be oxygen enriched?




Do not meddle in the affairs of wizards, for you are crunchy and taste good with ketchup.\"--- Marcel Marceau
View user's profile Visit user's homepage View All Posts By User
svm
Harmless
*




Posts: 31
Registered: 21-7-2004
Member Is Offline

Mood: No Mood

[*] posted on 13-8-2004 at 11:22


I think the metal does catalyze the decomposition of the peroxides (probably to water). I think it's fairly safe since it keeps the overall amount of peroxides very low. when you get a build up of peroxides and then decompose them all at once, then you have a problem.

so I think that as long as you toss the metal in before you start heating, you should be okay.
View user's profile View All Posts By User
unionised
International Hazard
*****




Posts: 5127
Registered: 1-11-2003
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 14-8-2004 at 04:04


Trinitrotoluene,
If I read your post correctly then in a quart of solvent you found half a teaspoon of impurity.
Are you going to go back to the shop and complain that it's only 99.7% pure?

Just as an aside, do you know what diacetone alcohol and mesityl oxide smell like?
They are formed by boiling acetone in alkaline conditions. Most glass is alkaline.
View user's profile View All Posts By User
Democritus of Abdera
Harmless
*




Posts: 47
Registered: 5-8-2004
Location: The Prefecture of Abdera in the region of Xanthi.
Member Is Offline

Mood: Stone Dead

[*] posted on 14-8-2004 at 05:33
I wasn't aware that borosilicate was alkaline.


and grateful for the info...

But I can support TNT on one point, the residue. THe apparatus I used was steel and constructed from two steel drums, I'll describe in another thread. (I used a great deal more solvent and also tried various other solvents, acetone, toluene, xylene, methyl hydrate, and most often of all I used white gas (hexane) and the result was always the same, if it came in a metal can, it had the same damn residue (rust inhibitor)




Do not meddle in the affairs of wizards, for you are crunchy and taste good with ketchup.\"--- Marcel Marceau
View user's profile Visit user's homepage View All Posts By User
trilobite
Hazard to Others
***




Posts: 152
Registered: 25-2-2004
Location: The Palaeozoic Ocean
Member Is Offline

Mood: lonely

[*] posted on 14-8-2004 at 08:32


I wouldn't be afraid of acetone leaving behind an explosive peroxide residue unless the acetone was already used in a way that could lead to formation of peroxides. No solvent handbooks warn of this, someone would surely had an accident if it was as commonplace as with ethers.
View user's profile View All Posts By User
Democritus of Abdera
Harmless
*




Posts: 47
Registered: 5-8-2004
Location: The Prefecture of Abdera in the region of Xanthi.
Member Is Offline

Mood: Stone Dead

thumbup.gif posted on 14-8-2004 at 08:57
Perhaps


the "warning about OTC solvents" that TNT felt worth mentioning was aimed more towards those attempting to obtain a pure product than any possible dangers.

Still, I have read, that as a general rule, it is bad form to distil even close to dryness.




Do not meddle in the affairs of wizards, for you are crunchy and taste good with ketchup.\"--- Marcel Marceau
View user's profile Visit user's homepage View All Posts By User
maj
Harmless
*




Posts: 2
Registered: 18-4-2005
Location: wouldn\'tyaliketoknow. BFE
Member Is Offline

Mood: glowing baby...

[*] posted on 18-4-2005 at 08:37
distilling solvents


When distilling some solvents (I.E. Ether) Copper is always a welcome addition.
View user's profile View All Posts By User
Quince
National Hazard
****




Posts: 773
Registered: 31-1-2005
Location: Vancouver, BC
Member Is Offline

Mood: No Mood

[*] posted on 18-4-2005 at 22:07


Likely the acetone from a drug store is more pure, and is what I use as a reagent. It is a good deal more expensive, but that's not an issue unless one is doing a large scale synthesis.

I'd like to inquire as to the purity of drain cleaner H2SO4. Someone mentioned that they add buffers to prevent heating in drains, and I've seen a dense impurity in the bottle of the clear drain cleaner. How likely is this to be a problem? Distillation of H2SO4 is a pain.




\"One of the surest signs of Conrad\'s genius is that women dislike his books.\" --George Orwell
View user's profile View All Posts By User
cyclonite4
Hazard to Others
***




Posts: 480
Registered: 16-11-2004
Location: is unknown
Member Is Offline

Mood: Amphoteric

[*] posted on 18-4-2005 at 22:26


Quote:
Originally posted by maj
When distilling some solvents (I.E. Ether) Copper is always a welcome addition.


Why did you open up an 8 month old thread to mention that? It has already been covered in the Diethyl Ether thread.

Anyways, adding a metal such as copper or silver does not decompose peroxides, it prevents formation of them. If it were a catalyst to peroxide break-down, think how much more trouble it would cause.




\"It is dangerous to be right, when your government is wrong.\" - Voltaire
View user's profile View All Posts By User This user has MSN Messenger
Organikum
resurrected
*****




Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline

Mood: frustrated

[*] posted on 19-4-2005 at 07:59


When distilling ether one adds some ferrous sulfate to the flask - this breaks down existing peroxides.
Into the receiving and storage vessel one adds some pices of copperwire what prevents further peroxide formation, does NOT break down existing peroxides though.

I never heard about dangers distilling acetone, I believe this being a myth - at least something what never happens in reallife.

/ORG




Irgendwas is ja immer
View user's profile View All Posts By User
mick
Hazard to Others
***




Posts: 338
Registered: 3-10-2003
Member Is Offline

Mood: No Mood

[*] posted on 17-5-2005 at 13:25


Never distil an ether to dryness because the bit that is left could be a peroxide. Di-isopropyl ether is the one to watch, any crystals and be careful.
mick
View user's profile View All Posts By User

  Go To Top