| Pages:
1
2
3
4 |
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Ramium  | is it possible that i added to much HCL so when the copper phosphate formed it was dissolved by the HCL forming a solution
|
Yes but it doesn't matter: as Tear's experiment and my calcs show H3PO4 will not precipitate copper phosphate from CuCl2 solutions.
For future efforts you will need to keep tight control of the amount of HCl used to dissolve the copper basic carbonate. If you 'overshoot' and the
resulting solution is acidic then you need to neutralise the excess HCl with NaOH.
You will need to neutralise some of your 5.1 M H3PO4 with NaOH solution to get a Na3PO4 solution.
H3PO4 + 3 NaOH === > Na3PO4 + 3 H2O
[Edited on 3-2-2015 by blogfast25]
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Rather than use NaOH, you can also add simple baking soda(sodium bicarbonate) to a solution of your phosphoric acid until the fizzing stops and then
add a small amount of additional phosphoric acid to destroy excess base. Be sure not to add the sodium bicarbonate too fast, as the reaction bubbles a
lot and can easily cause the solution to overflow.
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
Yes Ramium. Your Copper Phosphate is still in solution, and needs a base to precipitate it.
I have to give you a LOT of credit for your age. You managed to hang w/ the big dogs. All the while keeping track on your project.
Good work.
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by No Tears Only Dreams Now | | Rather than use NaOH, you can also add simple baking soda(sodium bicarbonate) to a solution of your phosphoric acid until the fizzing stops and then
add a small amount of additional phosphoric acid to destroy excess base. Be sure not to add the sodium bicarbonate too fast, as the reaction bubbles a
lot and can easily cause the solution to overflow. |
Yes, that would work.
Did you remove that link to 'wikia' on copper phosphate? If so can you post it again? I'd like to comment there that CuCO<sub>3</sub>
simply doesn't exist.
|
|
|
Shivachemist
Harmless
Posts: 30
Registered: 1-2-2015
Member Is Offline
Mood: No Mood
|
|
Yeah Zombie is right. It precipitates only under alkaline conditions or at least the salt you using for precipitation must be neutral and we can use
any basic phosphate (trisodium phosphate) to precipitate it from the metallic salt. Does anyone have basic salt like Magnesium or Calcium acetate? or
even we can use trisodium phosphate for precipitation as it is alkaline in nature. Just wanted to show how it works. But I have only monosodium
phosphate which is almost neutral to slightly acidic.
|
|
|
Ramium
Hazard to Others
Posts: 144
Registered: 3-12-2014
Location: new zealand
Member Is Offline
Mood: Licit fish
|
|
So if i add a small amount of sodium bicarbonate to my solution copper phosphate will pricipitate???
|
|
|
Ramium
Hazard to Others
Posts: 144
Registered: 3-12-2014
Location: new zealand
Member Is Offline
Mood: Licit fish
|
|
Also my solution has turned greener is that bad???
[Edited on 4-2-2015 by Ramium]
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
It's simply continuing the reaction. It's actually a good thing.
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
Shivachemist
Harmless
Posts: 30
Registered: 1-2-2015
Member Is Offline
Mood: No Mood
|
|
Yep, but I would recommend you to use trisodium phosphate to precipitate phosphates as it is strongly alkaline in nature and cheap as well (cheaper
than phosphoric acid).
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
| Quote: Originally posted by blogfast25 |
Did you remove that link to 'wikia' on copper phosphate? If so can you post it again? I'd like to comment there that CuCO<sub>3</sub>
simply doesn't exist. |
I don't think I did, but here it is again: http://sciencemadness.wikia.com/wiki/Copper%28II%29_phosphat...
You've got me curious now, when did copper(II) carbonate stop existing? The wikipedia article appears to have changed quite recently, and there's also
now a wikipedia article on copper(II) phosphate that seems to disagree with most of the work I've done with the compound.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Ramium | So if i add a small amount of sodium bicarbonate to my solution copper phosphate will pricipitate???
|
No. The amount of sodium bicarbonate needs to be at least equivalent to the amount of phosphoric acid you originally added:
H3PO4 + 3 NaHCO3 === > Na3PO4 + 3 CO2 + 3 H2O
Just keep adding NaHCO3 slowly until fizzing stops and precipitation starts.
|
|
|
Metacelsus
International Hazard
Posts: 2531
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Will that reaction go all the way to trisodium phosphate, or will it stop at the disodium salt? Sodium bicarbonate isn't very basic, and the pKa of
disodium phosphate is 12.38, according to Wikipedia. You might need to use sodium hydroxide for the last deprotonation.
(Sorry, didn't read the full post. You might not need to deprotonate it all the way, as the copper phosphate will nonetheless precipitate.)
[Edited on 4-2-2015 by Cheddite Cheese]
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Cheddite Cheese | Will that reaction go all the way to trisodium phosphate, or will it stop at the disodium salt? Sodium bicarbonate isn't very basic, and the pKa of
disodium phosphate is 12.38, according to Wikipedia. You might need to use sodium hydroxide for the last deprotonation.
|
A small excess of NaHCO3 will create the pH in which phosphate ions can exist and you don't need much of it to exceed the solubility limit of copper
carbonate!
Ks = [Cu]<sup>3</sup>[PO4]<sup>2</sup> = 1.4 x 10<sup>-37 </sup>
For [Cu] = 1 M, [PO4] = (1.4 x 10<sup>-37</sup> <sup>0.5</sup> = 3.7 x 10<sup>-19</sup> or pPO4 = - log[PO4] = 18.4
Also:
[H3O]<sup>3</sup> [PO4]/[H3PO4] = K1 K2 K3
Assume [H3PO4] = 1 M and take - log of both sides:
3 pH + pPO4 = pK1 + pK2 + pK3
3 pH + 18.4 = 21.7 = > pH = 1.65
So even a quite partial neutralisation of the phosphoric acid will cause copper phosphate to <i>start</i> precipitating.
[Edited on 4-2-2015 by blogfast25]
|
|
|
Shivachemist
Harmless
Posts: 30
Registered: 1-2-2015
Member Is Offline
Mood: No Mood
|
|
Well, carbonates and bicarbonates are usually used to prepare Disodium hydrogen phosphate.
H3PO4 + 2 NaHCO3 ------> Na2HPO4 + 2 CO2 + 2 H2O
Then the solution should be warmed gently to expel excess of CO2 present in the solution. Disodium hydrogen phosphate is feebly basic in nature. So,
it may not precipitate phosphate if the salt solution is moderately or very acidic. But, It will work for neutral salts or feebly acidic salts I
believe.
However, trisodium phosphate can be obtained just by treating the aqueous solution of Disodium hydrogen phosphate with calculated quantity of Sodium
hydroxide solution.
Na2HPO4 + NaOH -----> Na3PO4 + H2O
The anhydrous form can be prepared by fusing it up with Sodium carbonate:
2 Na2HPO4 + Na2CO3 -----> 2 Na3PO4 + H2O + CO2
[Edited on 4-2-2015 by Shivachemist]
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Shivachemist | Well, carbonates and bicarbonates are usually used to prepare Disodium hydrogen phosphate.
H3PO4 + 2 NaHCO3 ------> Na2HPO4 + 2 CO2 + 2 H2O
Then the solution should be warmed gently to expel excess of CO2 present in the solution. |
Nah, just use NaOH:
H3PO4 + 2 NaOH === > Na2HPO4 + 2 H2O
|
|
|
Shivachemist
Harmless
Posts: 30
Registered: 1-2-2015
Member Is Offline
Mood: No Mood
|
|
That is possible too. There is always more than one route to prepare a compound.
[Edited on 4-2-2015 by Shivachemist]
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
The sodium phosphate(not precisely sure which salt) I produced to make my copper phosphate only used baking soda and phosphoric acid, and an excess of
this salt was sufficient to completely convert the copper sulfate I used.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Thanks for the wikia link, NTODN.
It does indeed not matter much which type of soluble orthophosphate is used, as long as the solubility product of copper phosphate is exceeded when
mixing the solutions.
|
|
|
Ramium
Hazard to Others
Posts: 144
Registered: 3-12-2014
Location: new zealand
Member Is Offline
Mood: Licit fish
|
|
So my understanding is if i add sodium bicarbonate very slowly to the solution untill the fizzing stops
The copper phosphate should pricipitate is that correct???
[Edited on 4-2-2015 by Ramium]
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
Yes, dissolving the bicarbonate in water first might help make it easier to control the amount you are adding. By adding the basic bicarbonate,
you're increasing the pH and consequently increasing the number of free phosphate ions in solution. I apologize, I completely forgot in my first post
that phosphoric acid doesn't dissociate much.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Actually, with a pK<sub>a1</sub> of 2.15 (Wiki) phosphoric acid is a fairly strong acid but subsequent deprotonations are quasi
non-existent in pure H3PO4 solutions.
[Edited on 4-2-2015 by blogfast25]
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
I meant that it doesn't dissociate much into PO43- ions, there are quite a bit of H+ and H2PO4- ions as
you said based on the pKa1.
|
|
|
Ramium
Hazard to Others
Posts: 144
Registered: 3-12-2014
Location: new zealand
Member Is Offline
Mood: Licit fish
|
|
I just added the sodium bicarbonate it bubbled up very high(3 times the volume of the origanil solution)the foam has bits of blue in it i think thats
the copper phosphate so i will let the sun debubble it then filter to get the copper phosphate
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Try and filter it off, wash and dry properly and determine yield.
|
|
|
Ramium
Hazard to Others
Posts: 144
Registered: 3-12-2014
Location: new zealand
Member Is Offline
Mood: Licit fish
|
|
Yes yes yes yes yes!!! It worked i got heaps thank you all so much i love you all
|
|
|
| Pages:
1
2
3
4 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
