| Search |
| [Next Page] |
Cast vs Plastic
[rquote=690611&tid=160145&author=PLSHY]I used a formula to calculate that the detonation vel ... |
1-2-2024 at 20:04
by: DennyDevHE77 |
Cast vs Plastic
Thanks for the pictures. But all in all, nothing amazing. Cast ETH has a density of 1.65-1.7 and a d ... |
1-2-2024 at 11:42
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
Weeblordd, don't worry so much about a detailed oxygen balance (ratio) calculation. All fuel compone ... |
31-1-2024 at 21:00
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
[rquote=690563&tid=160138&author=Weeblordd]Why not? You mean to cover my ears? Idk about tha ... |
31-1-2024 at 13:03
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
5-15 g of ETH is more than enough to detonate most powdered, low-pressure ammonium nitrate explosive ... |
31-1-2024 at 05:27
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
By the way, as I see it, here on the forum everyone is obsessed with safe detonators, either without ... |
30-1-2024 at 21:07
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
[rquote=690540&tid=160138&author=Etanol]You can use EGDN, PETN, ETN, acetone peroxide as a s ... |
30-1-2024 at 20:47
by: DennyDevHE77 |
Cheapest, best, most available ammonium nitrate sensitizers?
I'd like to add about the ammotropin. Its optimum density is 1.24 g/mL. At this density, the detonat ... |
30-1-2024 at 09:38
by: DennyDevHE77 |
Short question / quick answer - Thread
[rquote=690139&tid=26572&author=OneEyedPyro]ETN is 8 to 10mm[/rquote]
I'm a little surpri ... |
28-1-2024 at 20:19
by: DennyDevHE77 |
Picric acid via sulfanilic acid
Correction, after I decided to wash this red precipitate, this red substance dissolved almost immedi ... |
23-1-2024 at 22:32
by: DennyDevHE77 |
Practice
So, after getting all the reagents I needed, I decided to give it a try.
First of all, having mix ... |
21-1-2024 at 01:40
by: DennyDevHE77 |
Nitration of Tetramethylene dinitroethane tetranitrate
[rquote=687282&tid=159852&author=Microtek]or HNO3/P2O5.[/rquote]
Microtek, I once wondere ... |
15-1-2024 at 21:49
by: DennyDevHE77 |
PETN synth
The nitration reaction of ETN (at least when ammonium nitrate is used), proceeds much more calmly th ... |
15-1-2024 at 20:55
by: DennyDevHE77 |
How to plasticize ETN with SBR (styrene-butadiene rubber)?
I'll be honest, I wrote this because I remembered an ancient discussion on a dead forum. I found it ... |
12-1-2024 at 09:34
by: DennyDevHE77 |
PETN synth
That's not the point. When using a mixture of nitric and sulfuric acid, it also partially converts p ... |
11-1-2024 at 05:58
by: DennyDevHE77 |
Guess the Propellant
I apologize. Didn't think of this obvious fact, I admit my mistake. I guess I thought of dinitramide ... |
11-1-2024 at 05:48
by: DennyDevHE77 |
PETN synth
Has anyone tested the product above on a chromatograph? How does it match PETN obtained with pure 98 ... |
11-1-2024 at 02:29
by: DennyDevHE77 |
My problem with pure fuming hno3
Well, that's how I clean 95% nitric acid. With urea. The nitric acid went from yellowish red to gree ... |
10-1-2024 at 23:21
by: DennyDevHE77 |
Guess the Propellant
I think it uses ammonium dinitramide as an oxidizing agent. In the USSR it was industrially produced ... |
10-1-2024 at 23:10
by: DennyDevHE77 |
My problem with pure fuming hno3
[rquote=635721&tid=155352&author=Microtek]The de-NOx-ing should be carried out at 50 C wheth ... |
10-1-2024 at 03:14
by: DennyDevHE77 |
Catalysts for NaNO3 black powder?
I believe finely pelletized black powder on sodium nitrate exploded from a detonator primer may show ... |
9-1-2024 at 04:40
by: DennyDevHE77 |
question about primaries
[rquote=690009&tid=159936&author=ManyInterests]while on paper, TATP has a higher VOD, in rea ... |
8-1-2024 at 21:05
by: DennyDevHE77 |
Short question / quick answer - Thread
Guys, could someone please point me to the critical diameters of cast ETN, TNT, and picric acid? I f ... |
8-1-2024 at 11:55
by: DennyDevHE77 |
Trinitrotoluene preparation
The big advantage here is that cleaning is optional. Of course, it can be recrystallized from alcoho ... |
8-1-2024 at 11:31
by: DennyDevHE77 |
How to plasticize ETN with SBR (styrene-butadiene rubber)?
[rquote=689952&tid=160090&author=EF2000]DennyDev is apparently using same thing, maybe from ... |
8-1-2024 at 11:24
by: DennyDevHE77 |
| [Next Page] |
