Sciencemadness Discussion Board
Not logged in [Login - Register]
Go To Bottom

Search
[Next Page]
Thinning solid fat/oils for injecting (venturi air suction) into forge?
[rquote=525597&tid=85657&author=RogueRose]
I've never mixed diesel or kerosene with oil, ID ...
25-7-2018 at 16:42
by: gnitseretni
Thinning solid fat/oils for injecting (venturi air suction) into forge?
[rquote=525490&tid=85657&author=RogueRose][
Have you ever used old motor oil as a fuel? Th ...
24-7-2018 at 14:38
by: gnitseretni
Life after detonation
[rquote=518721&tid=22554&author=coppercone]i also say I really dislike this fireking guy. ki ...
10-7-2018 at 20:01
by: gnitseretni
Making an induction heater for fastener removal?
If possible, weld a short bolt to the drain plug so you can put a wrench on the bolt. That's what I' ...
3-12-2017 at 10:32
by: gnitseretni
Electrical help?
I'm guessing something like this would work fine?

http://www.ebay.com/itm/24VDC-21A-Deltron-Singl ...
21-9-2016 at 15:03
by: gnitseretni
Electrical help?
Yeah there's two gearboxes in the picture. The motor is attached to the gearbox on the left. You can ...
21-9-2016 at 14:33
by: gnitseretni
Electrical help?
I think I left out some key information: I'm trying to stay as low cost as possible. I don't need to ...
20-9-2016 at 18:59
by: gnitseretni
Electrical help?
Thanks.

I've looked around for 24 Vac transformers. They don't say anything about bridge rectifie ...
20-9-2016 at 17:23
by: gnitseretni
Electrical help?
I want to make a square tubing roller to roll arches for driveway gates. I can get a discarded gate ...
20-9-2016 at 15:20
by: gnitseretni
Reagents for energetic materials for sale in houston
Update:

Everything's sold!
22-4-2016 at 09:00
by: gnitseretni
Unconventional Shaped Charges
Nice one Neonpulse!

Those electroformed liners work pretty good huh?! And they're easy to make!
19-4-2016 at 18:16
by: gnitseretni
Reagents for energetic materials for sale in houston
I'm done with energetic materials and I'm looking to sell the chemicals I have left over.

Note: I ...
19-4-2016 at 14:13
by: gnitseretni
PETN synth
I don't think the trouble is worth it. Only if you're specifically after PETN for some reason. Other ...
13-1-2016 at 20:25
by: gnitseretni
Unconventional Shaped Charges
Very nice!

I would increase standoff even more. That first hole is pretty big. It takes a lot of ...
18-9-2015 at 10:12
by: gnitseretni
Unconventional Shaped Charges
[rquote=419201&tid=10575&author=nux vomica][rquote=419176&tid=10575&author=gnitseret ...
14-9-2015 at 04:24
by: gnitseretni
Unconventional Shaped Charges
Nice work Nux! But you sure are making me miss the days when I made shaped charges. Lol!

Based on ...
13-9-2015 at 09:59
by: gnitseretni
Unconventional Shaped Charges
Nicely done!

Angle looks bigger than 50 degrees though. Dunno, maybe the picture makes the angle ...
1-9-2015 at 04:26
by: gnitseretni
Unconventional Shaped Charges
I don't think you have enough head height there but I hope I'm wrong. The smaller the angle the more ...
23-8-2015 at 06:29
by: gnitseretni
Unconventional Shaped Charges
Make a cone out of thinner copper sheet. I think that will improve results if everything else is kep ...
22-8-2015 at 10:26
by: gnitseretni
Unconventional Shaped Charges
Nice work nuxy! Maybe try different thickness cones while keeping else the same to try to improve re ...
21-8-2015 at 14:11
by: gnitseretni
PLX type explosives
Thanks for that PDF Dany!
11-1-2014 at 08:21
by: gnitseretni
EGDN vs. NG
I read that a mix of PGDN/EGDN is more powerful than either on its own. Read it in a patent though. ...
8-1-2014 at 20:40
by: gnitseretni
Sensitize Nitromethane for a rifle bullet round?
Not sure if it's bullet sensitive (I used a detonator), but I've successfully detonated NM sensitize ...
25-12-2013 at 08:11
by: gnitseretni
Quicksilver??
Has anyone heard from Quicksilver yet? I can't help but think that something must have happened to h ...
15-12-2013 at 19:37
by: gnitseretni
Pentaerythritol total synthesis
What are you going to do with the pentaerythritol? Just curious since you mentioned plenty of times ...
14-7-2013 at 15:06
by: gnitseretni
[Next Page]

  Go To Top