friendlyterry
Harmless
Posts: 9
Registered: 29-9-2009
Member Is Offline
Mood: No Mood
|
|
condenser length?
hi, whats the difference between a 200mm and a 500mm condenser ? how does it affect reflux?
|
|
User
Hazard to Others
Posts: 339
Registered: 7-11-2008
Location: Earth
Member Is Offline
Mood: Passionate
|
|
-A lot of money.
-More effective cooling.
Well it does depend on your purpose and batch sizes.
Also if you have a smaller cooler the flow rate must be lower to obtain higher yields.
[Edited on 1-10-2009 by User]
What a fine day for chemistry this is.
|
|
friendlyterry
Harmless
Posts: 9
Registered: 29-9-2009
Member Is Offline
Mood: No Mood
|
|
for small batches is 200mm ok?
[Edited on 1-10-2009 by friendlyterry]
|
|
entropy51
Gone, but not forgotten
Posts: 1612
Registered: 30-5-2009
Member Is Offline
Mood: Fissile
|
|
Although I have mostly 300mm condensers, I recently bought a couple of 200 mm and I like them very much. They seem adequate for everything except the
very low boiling point solvents. They take up less space for a downward distillation and don't crowd the hood as much as longer condensers. So far I
have had no trouble refluxing ethanol, chloroform, ethyl acetate, toluene, or acetic acid with a 200 mm condenser. The ring of condensate doesn't
rise more than a couple of cm into the reflux condenser. When refluxing there's no need to see how fast you can boil it because the reaction
temperature will not go above the BP of the solvent, no matter what. User, I don't
understand. Higher yields of what? Distillate?
[Edited on 1-10-2009 by entropy51]
|
|
JohnWW
International Hazard
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
For a shorter water-cooled condenser (with the water flowing through either a coiled tube or a jacket), you would certainly need either a faster flow
of cooling water, or water at a lower temperature, to obtain higher yields of condensate, compared to a longer condenser, because of the smaller
heat-transfer surface. The extent of cooling and condensation of the vapor desired to be collected in a flask would also depend on the thermal
conductivity of the material (usually borosilicate glass) of the coiled tube containing the water or (in a jacket type) the partition between the
water and the vapor.
|
|
UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
If you want to reflux, I suggest you try to pick up a Freidrich condenser on a good deal. They'll cost a bit more than the average condenser, but I've
never had condensing solvent make it even halfway up the cooling section. It's essentially a high-efficiency cold finger in it's own housing.
If you want multipurpose, a longer leibig will give better condensing for low boiling solvents, but they are bulky when being used for standard
distillation.
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
User
Hazard to Others
Posts: 339
Registered: 7-11-2008
Location: Earth
Member Is Offline
Mood: Passionate
|
|
@entropy51
Sorry i was a bit unclear.
I meant that a shorter condenser is more likely to loose product thus decreasing the amount obtained.
I would recommend spending a bit more money when its your first condenser, this would provide more applications.
What i often do is: using a vacuum adapter and a flask on the receiver end under ice or cold water.
This will make up a little for condenser loss as the gas that failed to condensate in the cooler will on the walls of the receiver.
I do this only when I am working with small amounts, and volatile substances.
* damn entropy you were faster relying than me editing *
[Edited on 1-10-2009 by User]
What a fine day for chemistry this is.
|
|
entropy51
Gone, but not forgotten
Posts: 1612
Registered: 30-5-2009
Member Is Offline
Mood: Fissile
|
|
If you lose product, you're distilling too fast! Turn down the fire.
Especially if you're fractionating something, you must distill slowly to get any separation of the components.
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
Separation of components in fractionation principally depends upon 1) Height and effectiveness of packing and 2) Reflux Ratio.
The "Size of Fire" must be so adjusted to avoid the flooding of column.
gsd
|
|
entropy51
Gone, but not forgotten
Posts: 1612
Registered: 30-5-2009
Member Is Offline
Mood: Fissile
|
|
I'm not going there. This has been hashed out repeatedly in several other threads.
Anyone who ever did a careful fractionation knows that you have to distill slowly to get good separation. The best column in the world won't separate
anything if you rush it. Simple as that. No armchair theorizing needed here.
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
Armchair theorizing? LOL!
I have been doing "careful" fractionation of close boiling cuts for past several years.
Your confusion is evident when you say slowly. Which probably means using very high reflux ratio thereby taking out very little amount of product as
compared to the amount of vapours going to the condenser.
In practice if you are actually adjusting your heating rate so as to reduce amount of vapour reaching condenser, then what you are unknowingly doing
is increasing the "internal reflux ratio"
And BTW keep your comments to the content of the post. Not on your perceived state of the poster
gsd
|
|
entropy51
Gone, but not forgotten
Posts: 1612
Registered: 30-5-2009
Member Is Offline
Mood: Fissile
|
|
Quote: Originally posted by gsd |
Which probably means using very high reflux ratio thereby taking out very little amount of product as compared to the amount of vapours going to the
condenser. |
Which definitely displays your confusion.
If you had done
them slowly you could have done them in a month or so instead of repeating them over and over with no separation.
[Edited on 1-10-2009 by entropy51]
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
@entrioy51
I am liberal enough to appreciate your pathetically laughable attempt to generate humour by twisting the meaning of a sentence. A very nice way to win
an argument when you are devoid of any substance
gsd
[Edited on 2-10-2009 by gsd]
|
|