avi66
Harmless
Posts: 46
Registered: 8-4-2010
Member Is Offline
Mood: No Mood
|
|
house 40ampers phase limitation ?
i want to run a big cell on 50 amper current, but i can't because my house electricity phase design to deliver max 40amper total, my question is, if i
use 2 cell inline using 12 volt, with 25 amper current, i will double the yield ?!?! i will get a yield equal to 50 amper cell by using 2 inline 25
amper cells ?!?! or my phase will jump, because 2 cells on 25 amper current will rise the total phase current to 50 amps?
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
In simple terms, neglecting AC and losses.
So your house has 40 Amp MAINS current. That's 40 Amps at say (whatever) 230 Volts.
Power = Voltage x Current = 230 x 40 = 9200 Watts = 9.2 KW
Methinks you could run quite a few cells with 9.2 KW
Your cell is say 50 Amps (Hah!.. do you realise how hot it will get) at say 4 Volts, that's 50 x 4 = 200 Watts = .2 KW
You could therefore run 46 cells.
I hope you are using a transformer or some sort of low voltage power supply, please don't connect your cell directly to the mains
Edit: Yes, two separate cells in series, operating at twice the voltage and half the current will be the same as one larger cell. The power consumed
will be the same!
[Edited on 28-1-2011 by Xenoid]
|
|
ScienceSquirrel
International Hazard
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination!
|
|
That's not electricity!
I have three phase with each phase rated at 150 Amps.
So 230 x 150 x 3 = 103500 Watts = 103.5 kW
But I am working in light industrial premises so normal household rules do not apply.
|
|
avi66
Harmless
Posts: 46
Registered: 8-4-2010
Member Is Offline
Mood: No Mood
|
|
so in 1 phase i can use up to 9200 Watts, divide it to 5 volts =1840A, you want to tell me that in 1 free house phase i can run a cell with 1840A ?
and if i use the 12 volts output its will be:
V*I=W
12*X=9200(ONE PHASE)
X=9200/12 (766A)
Then i will be able to use up to 766A at one phase ?
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Yeeeee....ss...s! In very simple terms, neglecting losses, etc. But you will need VERY thick cables to carry 766 Amps
What sort of a power supply are you planning on using for this 50 Amp cell. You'll need thick (welder, jump start) type cables for 50 Amps.
By the way, are we talking about a chlorate cell here!
|
|
IrC
International Hazard
Posts: 2710
Registered: 7-3-2005
Location: Eureka
Member Is Offline
Mood: Discovering
|
|
Idiotic configuration to so completely unbalance power pulling that many amps off of one phase. Use a 3 phase transformer, output as Wye, float
neutral and tap 2 phases, feed your 208 Vac single phase to low voltage high current transformer.
http://www.federalpacific.com/university/transbasics/chapter...
A few more ideas:
http://www.equitech.com/faq/3phase.html
http://cr4.globalspec.com/thread/27383/Three-Phase-to-Single...
[Edited on 1-28-2011 by IrC]
"Science is the belief in the ignorance of the experts" Richard Feynman
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Well of course! You don't seriously think it's going to happen do you
|
|
avi66
Harmless
Posts: 46
Registered: 8-4-2010
Member Is Offline
Mood: No Mood
|
|
i don't need 766 amper for my cell, i just need 60 A/H maximum, i got mmo anode with the size 5x0.3x36cm(30 in sol) which have surface area of 300c^2
multiple by 200 ma per square cm is 60000 ampers .... i will use probebly 50 ampers with 3 computer power supply 5 volts output.
its just hard to believe that my home can deliver at each phase at list 1500 ampers ... multiple by 3 is 4500 ampers ... i can open a chlorate factory
!!!!
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Quote: | ... i can open a chlorate factory !!!! |
Given the apparent state of your knowledge of electricity, you also have a good chance of electrocuting yourself!
Your time, it seems, would be better spent reading up on all things electrical . . .
|
|
avi66
Harmless
Posts: 46
Registered: 8-4-2010
Member Is Offline
Mood: No Mood
|
|
I whas just joking man .... just talking theoretically, Thanks for help peoples.
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
I'm guessing you were also planning to just hook up those three power supplies in parallel to your cells, right?
Seriously, take hissingnoise's advice and spend a bit of time so you understand the basics at least.
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer
|
|
avi66
Harmless
Posts: 46
Registered: 8-4-2010
Member Is Offline
Mood: No Mood
|
|
if i have a a barrier which capable of standing 50 ampers current , and 3 dc power supply which capable Carrie 20 ampers at 5 volts each one, i will
be able to start all of 3 power supply and then open the barrier, so all they power supply will be able to give 50 ampers hours together ?!
|
|
dann2
International Hazard
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Hello Folks,
50 Amps is not a bad size of cell to start off with (shakes head). Suppose it's a case of, reach for the stars and you will (probably) get to the tree
tops
You can try paralling your three computer power supplies by connecting the three outputs (red, +5V) to the Anode and having three Cathodes. Each
Cathode will need to be connected to a seperate black wire(s) from each (computer) power supply. That's the only way I know of combining (in
parallel) computer power supplies for this type of application. Manipulate the spacings to get each supply to supply approx. 17 Amps of current.
You will have a bang if you connect the supplies in parallel to one Anode and one Cathode IMO.
You could simply cut your MMO and make three 20 Amp Anodes and run smaller (more sensible size for a beginner) Cells.
See here for some wise words of wisdom!!
http://oxidizing.110mb.com/chlorate/powersup.html
@phlogiston Have you used that signature for long in your career?????? Just wondering. It takes me back........
I believe he once said>
I aim ALL my rockets at the moon.
Sometimes they happen to land on London.
Dann2
[Edited on 28-1-2011 by dann2]
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
Avi6, from your last post I suspect you believe that you need a 50 ampere supply to reach 50 Ah. If so, then you will probably enjoy learning that you
can reach the same number of Ah's with any supply, it will just take longer. With a 50A supply, it takes one hour to reach 50Ah. With 25A, it takes 2
hours. With a more reasonable 2 A and a tiny anode, it will still only take a day. With that 776A supply you previously considered it will take 3
minutes and 52 seconds
Dann2, yes, c'est moi. It's been a while... lovely to see you never left this alone for all this time. Can you imagine how I enjoyed reading the
immense progress that has been made here with respect to homebrewing anodes when I discovered this forum!
Re the .sig:I recently found out it actually came from a brilliant song by the comedian Tom Lehrer (http://www.youtube.com/watch?v=kTKn1aSOyOs). I guess I've got to change it now.
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer
|
|