thebolter
Harmless
Posts: 2
Registered: 27-12-2013
Member Is Offline
Mood: No Mood
|
|
Nitrating toluene with KNO3
I was wondering if it was possible to nitrate toluene with potassium nitrate instead of nitric acid.
My previous attempt resulted in a brown liquid which did not turn yellow. Toluene was slowly added to a stirred, over saturated solution of
concentrated sulfuric acid and potassium nitrate at 20-30C.
Anyone ever try this before?
|
|
|
Zyklon-A
International Hazard
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
I'm quite sure if it is possible, everybody would do it/know about it.
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Yes, conc. sulfuric acid and KNO<sub>3</sub> will nitrate toluene. Mostly to the di nitrate. Some TNT likely results if some mild reflux
is applied. Better to try the nitration in steps, then worry about seperation of the lower nitrated products and other crap. Including the potassium.
Oh, and dont use a suspension. Make a conentrated solution of the nitrate salt in the acid. Use gentle heat and stirring. Make sure the nitrate salt
is very dry and fine. Try anhydrous sodium nitrate for better results.
Remember these nitrations create NOxious gasses and the products present a health risk. Skin contact is to be avoided.
Also check the physical data on MNT, DNT, and TNT, and mixes there of.
[Edited on 28-12-2013 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
thebolter
Harmless
Posts: 2
Registered: 27-12-2013
Member Is Offline
Mood: No Mood
|
|
I should have mentioned that my desired product is MNT.
Also, shouldn't heating be avoided to avert explosions?
|
|
|
Lambda-Eyde
National Hazard
Posts: 858
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Your toluene likely contains thiophene which results in a brown/black mess when treated with conc. sulfuric acid. I ran into the same problem a while
back: http://www.sciencemadness.org/talk/viewthread.php?tid=17783
I was under the impression that TNT required oleum?
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
Nicodem
|
Thread Moved
28-12-2013 at 00:20 |
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Oleum and conc. nitric acid is the best way to get TNT. Some can be formed with conc. sulfuric, and anhydrous nitrate salt or strong nitric acid if a
long enough reaction is carried out at the right temps. I have seen this on test tube scales, and quicksilver discussed it on many occasions, IIRC.
Elevated temps are needed. This isnt nitroglycerin, an ester. Its an aromatic nitration. Heat is required
[Edited on 28-12-2013 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
bfesser
|
Thread Moved
28-12-2013 at 07:48 |
Turner
Hazard to Others
Posts: 197
Registered: 2-12-2013
Member Is Offline
Mood: No Mood
|
|
Bot0nist, you always push your "UTFE" stuff, but could you post a link or a reference to the nitration from DNT to TNT w/out the use of Oleum but
using harsher conditions? (more heat, more sulfuric acid, etc.)
I searched plenty, I've read the whole 8 page thread on TNT.
|
|
|
Turner
Hazard to Others
Posts: 197
Registered: 2-12-2013
Member Is Offline
Mood: No Mood
|
|
Does "Klean-Strip" Toluene contain thiophene?
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Turner, you have me at a loss. I searched a bit and cant locate what I know I have read and attempted. In the next two weeks I will try to recreate
the experiance and post my results, as I have no notes. I can measure purity roughly with a rigged melting point apperatus and physical properties. I
lack a few reagents and liquidity at the moment. Will update.
[Edited on 28-12-2013 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
