Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
 Pages:  1  2
Author: Subject: Electrolytic Production of Sulphuric Acid + some questions.
chief
National Hazard
****




Posts: 630
Registered: 19-7-2007
Member Is Offline

Mood: No Mood

[*] posted on 21-2-2009 at 15:00


Right. What then about the really available and cheap sulfate: CaSO4 aka gypsum: This is soluble in water (0.2 g/100 ml), and maybe used for diaphragma at the same time too . Only the conductivity will be lower than with other electrolytes ...

The most simply-thinkable cell of this would have it for diaphragma in the middle of the cell, as some sort of a wall. Then on the one side of it H2SO4 would accumulate, and on the other Ca(OH)2 would make the water milky ...

To tune up the efficiency of this one might have to make the surface big enough and put the electrodes close enough together to limit the current-losses.

Besides the mentioned pyrosulfate is a big-scale industrial product ; used everywhere in the food-industry .

[Edited on 21-2-2009 by chief]
View user's profile View All Posts By User
DerAlte
National Hazard
****




Posts: 779
Registered: 14-5-2007
Location: Erehwon
Member Is Offline

Mood: Disgusted

[*] posted on 23-2-2009 at 21:20


Instead of calcium, magnesium is better. The sulphate is quite soluble and cheap (fairly pure too, as fertilizer). This requires a divided cell, the Sulphate being converted to Mg(OH)2 and precipitated at the cathode.

Simplest of all, any platable metal sulphate could be used in an undivided cell, the metal ion being plated on the cathode . Fe, Cu Ni etc. could be used. Iron(II) sulphate is also a cheap fertilizer. The rest are more expensive.

Regards, Der Alte
View user's profile View All Posts By User
not_important
International Hazard
*****




Posts: 3873
Registered: 21-7-2006
Member Is Offline

Mood: No Mood

[*] posted on 24-2-2009 at 03:01


In the divide cell the increasing concentration of OH(-1), H(+1), HSO4(-1) and SO4(-2) will also result in increasing pressure driving those ions across the membrane. This is why most attempts at commercialising this sort of process use ion-selective membranes in various arrangements.

When plating out a metal the hydrogen ion concentration rises until the production of H2 rivals that rate of plating out the metal, and then exceeds it. In electro-analytic chemistry almost all the metal can be plated out, but this frequently requires additives that would run the acid produced as a reagent.

So those are effects that will compete with the production of useful grades of acid and base. It can be done, I've read of a plant that split a waste (NH4)2SO4 stream into H2SO4 and "NH4OH" using a multistage electro-dialysis process with ion-selective membranes.
View user's profile View All Posts By User
mysteriusbhoice
Hazard to Others
***




Posts: 477
Registered: 27-1-2016
Member Is Offline

Mood: Became chemistry catboy Vtuber Nyaa

[*] posted on 6-10-2017 at 08:57


what if you add CaSO4 in the cathode area of the cell
make sure its hydrated first or you will end up with a solid block!!
it should continue to pull out the SO4 ions from the CaSO4 and regenerate the small amount of NaOH used
while keeping the sodium concentration low in the anode side!!
Ca(OH)2 is not soluble in water just make sure no CO2 enters the cathode are or else ..... Cement
View user's profile Visit user's homepage View All Posts By User
 Pages:  1  2

  Go To Top