Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Can you make bromine in the separatory funnel?
NaK
Hazard to Self
**




Posts: 83
Registered: 12-9-2019
Member Is Offline


[*] posted on 4-2-2021 at 14:14
Can you make bromine in the separatory funnel?


Storing bromine is not a very good idea, so i wonder if it is possible to very quickly synthesize small amounts of bromine just in a separatory funnel.

Basically
- make HBr by adding sulfuric acid to potassium bromide solution
- add the ice-cold solution to a separatory funnel
- add h2o2
- separate bromine layer
- dry bromine with sulfuric acid

Why is it not usually done this way? Is there a fundamental problem I haven't thought of?
View user's profile View All Posts By User
Boffis
International Hazard
*****




Posts: 1874
Registered: 1-5-2011
Member Is Offline

Mood: No Mood

[*] posted on 4-2-2021 at 14:49


Yes, this is my standard method if I don't need dry bromine, e.g. if I am working in an aqueous environment. I use sodium bromide, sodium bromate and diluted sulphuric acid. The bromine sinks to the bottom and can then but run off directly into the reaction for which it is intended. If you want to you can then distill the sodium bisulphate solution to recover the last bit of bromine but I personally don't think its worth the effort.

If I need dry bromine then I usually distill it from excess sulphuric acid from a flask directly into a chilled receiver rather then use a dropping funnel but you could just run off the bromine into another funnel and add some sulphuric acid to dry it.

I am sure you could use other cocktails to generate the bromine. I find the benefit of this method is the minimum of exposure required of the bromine to the air (and hence me). The disadvantage is the volume of bromine per unit of solution is about 1:25 so that in my equipment I can only make about 20ml max (about 60g). The strength of the acid is important, too strong and sodium salts ppt about 30% seem optimal. The reaction is fairly exothermic but you can't chill the sodium salt solutions as this greatly reduces solubility so you need to make up the dilute acid and then chill it in the freezer beforehand.

Your mixture may be better than mine if it generates less sodium hydrogen sulphate. Hydrobromic acid free of sodium salts would be better still.
View user's profile View All Posts By User
pip
Hazard to Others
***




Posts: 109
Registered: 19-9-2008
Member Is Offline

Mood: No Mood

[*] posted on 4-2-2021 at 15:52


Most people don’t like to make bromine as they need it, they prefer to practice sealing ampules either commercial ones or homemade ones from test tubes. I prefer to make a lot at once and ampule it. Only because hobbiests are already limited on reagents and it’s one less procedure to go through when you have to make a bunch of chemicals you haven’t made before.

I’m a big fan of making a lifetime supply of something if possible (and safe) or at least as much as I think will last me a year or two. I bought 2ml and 5ml ampules from eBay cheap, makes it convenient to have 3-10g at my disposal without spending a few hours to do it. Also wastes less chemicals due to glassware losses.
View user's profile View All Posts By User
NaK
Hazard to Self
**




Posts: 83
Registered: 12-9-2019
Member Is Offline


[*] posted on 4-2-2021 at 17:56


Quote: Originally posted by pip  
I’m a big fan of making a lifetime supply of something if possible (and safe) or at least as much as I think will last me a year or two. I bought 2ml and 5ml ampules from eBay cheap, makes it convenient to have 3-10g at my disposal without spending a few hours to do it. Also wastes less chemicals due to glassware losses.


Yeah that's the common practice but I'm just very uncomfortable with having bromine around. It may be slightly irrational but a broken vial of bromine is one of the worst things I can think of. So for the few times I need bromine I will make it as needed

[Edited on 5-2-2021 by NaK]
View user's profile View All Posts By User
clearly_not_atara
International Hazard
*****




Posts: 2795
Registered: 3-11-2013
Member Is Offline

Mood: Big

[*] posted on 4-2-2021 at 18:07


I kind of imagine the real trick here is to use freezing-point depression so that you can solidify the bromine and just pour off the solution. For this one excellent candidate salt is potassium acetate, soluble roughly 200% w/v in water (that's not a typo). So roughly:

6 HOAc + 5 KBr + KBrO3 >> 6 KOAc + 3 H2O + 3 Br2

But you should use a 1.1-1.5x molar excess of acetic acid to ensure that the solution does not become too alkaline. Bromine freezes at about -7 C. Potassium acetate should be dissolved at roughly 50% w/v so the heat of reaction will be a significant factor (some additional KOAc might be added so the reaction can be run more dilute). To my knowledge, bromine does not attack acetic acid under these conditions.

But I haven't got a setup capable of working with bromine right now anyway :P All work and no play makes Jack a dull boy...

[Edited on 5-2-2021 by clearly_not_atara]




Quote: Originally posted by bnull  
you can always buy new equipment but can't buy new fingers.
View user's profile View All Posts By User
draculic acid69
International Hazard
*****




Posts: 1371
Registered: 2-8-2018
Member Is Offline


[*] posted on 5-2-2021 at 01:55


Quote: Originally posted by NaK  
Quote: Originally posted by pip  
I’m a big fan of making a lifetime supply of something if possible (and safe) or at least as much as I think will last me a year or two. I bought 2ml and 5ml ampules from eBay cheap, makes it convenient to have 3-10g at my disposal without spending a few hours to do it. Also wastes less chemicals due to glassware losses.


Yeah that's the common practice but I'm just very uncomfortable with having bromine around. It may be slightly irrational but a broken vial of bromine is one of the worst things I can think of. So for the few times I need bromine I will make it as needed

[Edited on 5-2-2021 by NaK]


It's not irrational at all, bromine is an untame-able monster
The horror potential is right up there.one little mistake
could be catastrophic to equipment, health, property or all 3

[Edited on 5-2-2021 by draculic acid69]
View user's profile View All Posts By User
njl
National Hazard
****




Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline

Mood: ambivalent

[*] posted on 5-2-2021 at 07:07


Similar idea, would an electrobromine cell in an addition funnel be advantageous? Anode at the bottom/cathode at the top, bromine forms and pools at the bottom, drain and repeat. What electrodes would work here?
View user's profile View All Posts By User
Fyndium
International Hazard
*****




Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline


[*] posted on 5-2-2021 at 09:44


Seal bromine in glass ampoules, place the ampoules in dual PE ziploc bag and freeze them. Now you have three(four) layers of protection against catastrophic failure.

Other than that, the funnel idea sounds quite convenient, as you will need to do preparations for a synthesis run anyway, adding an extra funnel shouldn't be an issue.
View user's profile View All Posts By User
Metallophile
Hazard to Self
**




Posts: 87
Registered: 23-3-2018
Member Is Offline

Mood: No Mood

[*] posted on 5-2-2021 at 12:48


What is the best way to dry bromine? I tried CaCl2, but it seemed to break apart and contaminate the Br with little bits of salt. Would 3A molecular sieves work? Or would they absorb the bromine too? Maybe drain cleaner grade H2SO4?
View user's profile View All Posts By User
njl
National Hazard
****




Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline

Mood: ambivalent

[*] posted on 5-2-2021 at 14:54


Shaking with H2SO4 is common
View user's profile View All Posts By User
draculic acid69
International Hazard
*****




Posts: 1371
Registered: 2-8-2018
Member Is Offline


[*] posted on 5-2-2021 at 19:03


Quote: Originally posted by Metallophile  
What is the best way to dry bromine? I tried CaCl2, but it seemed to break apart and contaminate the Br with little bits of salt. Would 3A molecular sieves work? Or would they absorb the bromine too? Maybe drain cleaner grade H2SO4?

Sulfuric is the only way
View user's profile View All Posts By User
NaK
Hazard to Self
**




Posts: 83
Registered: 12-9-2019
Member Is Offline


[*] posted on 14-2-2021 at 11:58


Tried it with hydrogen peroxide. I cannot recommend it at all! It can't be run cold because the reaction speed is too low. But when it goes up to room temperature thermal runaway immediately starts and all the bromine escapes. I wi just go for distillation next time
View user's profile View All Posts By User

  Go To Top