m1tanker78
National Hazard
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
Red Laser Pointer Reveals a Dirty Green Secret?
I bought a cheap red laser pointer to practice assembling optical trains, aligning mirrors and so forth. I observed on several occasions what I
believed were orange/yellow/green emissions after passing the beam through a dichroic filter set to maximum attenuation of the laser light and
observing the band(s) by eye with a diffraction grating. I should mention that the laser only emits ~5mW and the filter attenuates the vast majority
of the red light. I wouldn't dare look directly at any laser source -- not even low power ones.
At first, I dismissed those observations as being impossible, even from a cheap laser diode. I also had trouble reliably reproducing the effect.
Frankly, I expected to observe a few spectral lines right beside the main laser line since I didn't use a monochromator nor any 'cleanup filter' at
the output of the laser. Surprisingly, the laser line is fairly clean as far as my protected eye could detect.
I exploited the fact that diode lasers emit polarized light. (Mansuripur et al.) I placed a polarizing filter oriented cross-planar to the laser
source. The polarization filter greatly attenuates the laser beam. The dichroic filter was used to further attenuate the main laser line. The beam was
then passed through a diffraction grating or prism. The green component immediately became clear and after a bit of optimizing, I'm now able to
reliably reproduce this effect. Depending on the orientation of the laser and optics, the green and red bands could be maximally dispersed to clearly
distinguish them or can be made to overlap in order to observe the green-yellow-orange-red pattern. Based on that, it became clear that the yellow and
orange light I previously observed was simply the red and green lines overlapping with differing proportion of intensities.
What's the most likely cause of this anomaly from a supposed monochromatic light source?
-Impurity in the gain medium?
-Physical deformity of the cavity that causes out-of-band resonance?
-Fluorescence?
-Anti-Stokes peak of the focusing lens (probably epoxy)? Seems unlikely but...?
-I should just slap a narrow passband filter in front of the source and forget about this green co-emission business?
I was able to take some photographs but had a difficult time trying to align and focus the camera in the dark. I'd appreciate a reference or any
insight in this matter. I searched around and came up empty. Maybe I'm using the wrong search terms or something..
Dispersing:
<a href="https://picasaweb.google.com/lh/photo/zCyu-QLDTdH9KM0uu_XTwU-4EyEZuJxi0PQuPcSp7hM?feat=embedwebsite"><img
src="https://lh4.googleusercontent.com/--mR9x_hNcH4/VNAUoRtqs4I/AAAAAAAAAzk/Oix7g5IlMJY/s800/20150128_144548_cropped.jpg" height="388" width="548"
/></a>
Overlapping:
<a href="https://picasaweb.google.com/lh/photo/GjZopcaWr2fVh23hjpqHNU-4EyEZuJxi0PQuPcSp7hM?feat=embedwebsite"><img
src="https://lh3.googleusercontent.com/-yYRxlOi7_5s/VNAUobbd7yI/AAAAAAAAAzY/s16kgtFEENY/s800/20150128_152131_cropped.jpg" height="580" width="492"
/></a>
Chemical CURIOSITY KILLED THE CATalyst.
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
You must have a frequency leak or bleed over. Most likely is a bad timing crystal. It's the only logical explanation I can think of. Basically the
same as your first assumption.
Honestly with the cheap junk shipping out of China it is anyone guess as to which component is at fault.
I've made multiband lasers in the past, and timing, and pulse width were used to create "shots" that were measured with a timing light matching the
frequency. This was also 30 years ago.
I think you have a cute anomaly, and it had me thinking for a moment. In the end it is not surprising considering the source.
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
jock88
National Hazard
Posts: 505
Registered: 13-12-2012
Member Is Offline
Mood: No Mood
|
|
I have read that some of the high power lasers coming from china are emmiting far more power than stated. The power declared is only in the
colour-that-you-have-purchased band. The rest in the IR. Will demolish your eyes etc in a far shorter time than you would think.
|
|
|
The Volatile Chemist
International Hazard
Posts: 1981
Registered: 22-3-2014
Location: 'Stil' in the lab...
Member Is Offline
Mood: Copious
|
|
Interesting. I've had a laser pointed at my eyes by a teacher for 'being stupid' (When he left some space on the board, I told him he had to be
liberal, for he couldn't be a conservative-ist  ), who stated it wouldn't be able
to do any harm for a while.
Regardless, could the timing circuit, etc. be exploited for the production of other useful laser light?
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
That is what creates the color. The frequency at which the diode is run. It gets pretty complex depending on the pump type. Some lasers can be tuned
to run at different frequencies or in different spectrum's but essentially they are purpose built.
If you fiddled w/ yours to change frequency, what you would find is something very similar to your results in capturing the out of band emissions you
posted. There would be a VERY narrow range of variation where the light could be captured or in this case created.
The entire circuit you have to work with had a pre-determined frequency. You could change the pump, and the timing, but then you have a different
laser.
Soooo to get to brass tacks, you could tune to create a different color but the focus, and amplitude would be so far off that the result would be
negligible, and difficult to capture.
It was more fun (for me) to build a stepped pulse beam containing two colors. Using the correct timing the beam could be seen in either spectrum, and
as individual colors stopped in space. Little pieces of floating thread is what the effect was. Similar to a strobe timing light on a rotating object.
The object appears to stop in space.
Like I said, it's been a bunch of years so I found some links that are more in depth.
This is a good write up on the basics.
http://www.fas.org/man/dod-101/navy/docs/laser/fundamentals....
This is pretty cool too. It explains multi spectrum lasers, and has a few sentences that explain the phenomenon you experienced.
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC3270856/
[Edited on 3-2-2015 by Zombie]
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
Quote: Originally posted by The Volatile Chemist  | Interesting. I've had a laser pointed at my eyes by a teacher for 'being stupid' (When he left some space on the board, I told him he had to be
liberal, for he couldn't be a conservative-ist ), who stated it wouldn't be able
to do any harm for a while.
|
That seems very dangerous . Especially if it was a cheap laser pointer, those don't have the best quality control. In addition, the actual diode is much
stronger in many of them and the power is limited by a resistor(I believe).
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
They tend to use whatever diode is available in bulk (cheap), and yes the power output is modulated via the control circuit. Laser diodes need to run
on the ragged edge of self destruction anyway so these cheapo pointers can be all over the place as far as specifications are concerned.
Most of the companies manufacturing them have done NO development nor do they understand the circuit they are building. They simply reverse engineer,
and recreate the circuit. Hell the same factory runs watches, lasers, ignition modules, and coffee pots at the same time.
Their R&D departments consist of de-soldering stations, and cameras.
This should instill confidence...
http://www.alibaba.com/showroom/cardiac-pacemakers.html
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
m1tanker78
National Hazard
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
The package the laser came in states a wavelength range of 630 to 650nm. I went ahead and measured the wavelengths of the red and green lines with a
diffraction grating.
lambda=(d*sin(Φ)/n
lambda(red) = 646.35nm
lambda(green) = 549.45nm
I'm going to record input power vs temperature vs wavelength just as an exercise to see just how much the wavelength on one of these cheapies varies
with temperature and supply current. The higher power laser will dissipate much more heat and I'm sure I'll need to provide active cooling in order to
maintain stability.
Zombie:
I didn't modify anything in the circuit except to do away with batteries and use a buck converter. The green light appears even with batteries and
seems to be directly proportional in intensity to the red emission. Thanks for the links, the second one looks interesting!
Chemical CURIOSITY KILLED THE CATalyst.
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
Upping the current won't achieve anything other than stress test the components. It's the timing circuit that you have to change to directly see
results.
You might release more anomalies as the circuit stresses but that is a speculative matter, and I would think mostly non repeatable.
30 years ago we used timing crystals to control the timing or clock IC's. I couldn't remember a number if my life depended on it but I believe now the
IC is self regulated so looking up the control circuits specs you will have a base line to work from.
I was brainstorming as I was typing, and it came to me...
http://ichaus.de/LaserDrivers
Here's what I think you want...
http://www.arimalasers.com/attach/product/20120518095535_doc...
That's the start line.
Maybe I didn't forget as much as I forgot that I forgot.
Keep updating this. I'm R E M e m b e r i n g
[Edited on 6-2-2015 by Zombie]
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
m1tanker78
National Hazard
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Zombie | | Upping the current won't achieve anything other than stress test the components. It's the timing circuit that you have to change to directly see
results. |
I think you misunderstood my experimental conditions. What I want to do is measure the wavelength(s) of the laser emission while modulating the
current from, say, 5mA to the diode's max current rating. Set temperature in steps of ~2 deg. C within a range falling between 0 - 40 deg. C and
repeat the current stepping. In other words, sweep the current and measure laser line wavelength at each of a discrete set of temperatures. I hesitate
to complicate this since I won't be using the laser pointer for my final project.
EDIT:
I bought a 2nd laser pointer just to rule out a specific manufacturing defect on the first one. Same result with the green line. I removed the lens
from one of them and ruled out possibility of a frequency shift due to the lens material. The green emission is intrinsic to the laser chip.
[Edited on 2-8-2015 by m1tanker78]
Chemical CURIOSITY KILLED THE CATalyst.
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
I think that does back to cheap parts bought in bulk.
It's cool that you narrowed it down to that point tho.
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
Texium
|
Thread Moved
22-11-2023 at 19:12 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
