metalresearcher
National Hazard
Posts: 751
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
CaSO4 + Al in vacuum, what exploded ?
Yesterday I mixed some CaSO4 (burnt dead and crushed plasterboard) with Al powder in a 136:72 ratio and I ignited it electrically with an iron wire.
First in open air and then in vacuum.
It reacted vigorously without sound.
After the reaction the pressure within the 1 liter jar surged to from almost zero to 0.3 bar (02:04 in video) and when I let air into the jar (02:27,
slow motion at 03:06) a small dull explosion occurred with some light.
I am curious which flammable gas was in the jar. The only possibility would be H2 due to moisture in the mixture or the container (an YTONG cell
concrete bricklet).
Assume 1 liter of 0.25 bar = 1/100 mol H2 from 1/100 mol H2O which is 0.18 gr moisture. Would that be possible ?
https://www.metallab.net/jwplayer/video.php?v=L2NsaXBzL0NhU0...
|
|
RawWork
Hazard to Others
Posts: 167
Registered: 10-2-2018
Member Is Offline
|
|
Calcium Sulfate reduced to Calcium Sulfite, or Calcium Oxide and Sulfur Dioxide. Sulfur dioxide may have been reduced to sulfur and sulfide.
Depends...
Sulfur reacting with air to form sulfur dioxide.
Or sulfur dioxide reacting with air to form sulfur trioxide.
Or more reactions at once.
[Edited on 28-3-2018 by RawWork]
|
|
Sulaiman
International Hazard
Posts: 3658
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I think that there may be many chemicals in plasterboard added for differing reasons.
I'd try again with 'pure' reagents, if available.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
I recall some homes had to remove existing plasterboard for health reasons. Recollection was the use of cheap plasterboard containing formaldehyde
(see "An Investigation on Formaldehyde Emission Characteristics of Wood Building Materials in Chinese Standard Tests: Product Emission Levels,
Measurement Uncertainties, and Data Correlations between Various Tests", at https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4675528/ ).
[Edited on 29-3-2018 by AJKOER]
|
|
unionised
International Hazard
Posts: 5115
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Most things that might explain an explosion (and formaldehyde in particular) will not survive the process of powdering and dead burning.
Calcium sulphide is a fairly strong reducing agent. It's possible that it oxidised back to the sulphate.
|
|
wg48
National Hazard
Posts: 821
Registered: 21-11-2015
Member Is Offline
Mood: No Mood
|
|
I suggest you determine if the explosion is reproducible. If it is try different amounts of aluminium powder, different sources of the calcium
sulphate, a different sulphate, wait longer before allowing the air in so the initial react products have cooled down.
If you can adjust the camera so its set to a fixed lower sensitivity (so the image is almost black until the explosion occurs) you may be able to see
what ignites. Take safety precautions such as screen between you and the chamber just in case the next explosion is more violent.
|
|