Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Flying stoppers...
evil_lurker
National Hazard
****




Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline

Mood: On the wagon again.

[*] posted on 1-7-2007 at 18:05
Flying stoppers...


Don't ya just hate them?

When working with low boiling point stuff with high partial vapor pressures in a closed apparatus... you think everything is all good then next thing you know the stopper goes flying off and hits the ceiling. :mad:

Ahhh the joys of working in the laboratory.




Not all chemicals are bad. Without chemicals such as hydrogen and oxygen, for example, there would be no way to make water, a vital ingredient in beer.
View user's profile View All Posts By User
tito-o-mac
Hazard to Others
***




Posts: 117
Registered: 30-6-2007
Member Is Offline

Mood: No Mood

[*] posted on 6-7-2007 at 07:12


fit a bigger stopper? maybe try out a flask that has swrew on caps!
View user's profile View All Posts By User
Ozone
International Hazard
*****




Posts: 1269
Registered: 28-7-2005
Location: Good Olde USA
Member Is Offline

Mood: Integrated

[*] posted on 6-7-2007 at 16:51


Maybe not such a good idea!

Believe me, the stopper flying off can actually save your ass! I have had the side of a 2-L sep-funnel literally pop off (perfectly round piece of glass) b/c I had inadvertantly frozen the ground glass stopper (and there must have been a small crack in my funnel). This was with diethyl ether at ~28°C.

I always try to avoid "closed-systems"... I like to use a mercury bubbler, manometer or relief valve to keep this stuff straight (a spontaneous overpressure will give you bubbles, keep your mixture away from air and moisture, and save your precious glass!

And, erm, yes, I have had them hit the ceiling...then fall onto the apparatus and destroy it (heavy glass ones:o).

Ever notice that stuff like this tends to happen when someone is watching?

Sucks,

O3




-Anyone who never made a mistake never tried anything new.
--Albert Einstein
View user's profile View All Posts By User
flyingbanana
Harmless
*




Posts: 38
Registered: 1-3-2005
Member Is Offline

Mood: No Mood

[*] posted on 6-7-2007 at 20:05


makes me appreciate my goggles...imagine if it flew at your eyeballs! Always wear goggles!
View user's profile View All Posts By User
bio2
Hazard to Others
***




Posts: 447
Registered: 15-1-2005
Member Is Offline

Mood: No Mood

[*] posted on 6-7-2007 at 21:28


....."And, erm, yes, I have had them hit the ceiling...then fall onto the apparatus and destroy it (heavy glass ones:o"........

A kind of half ass relief valve can be had when using ground
glass pennyhead stoppers by inserting them loosely and tying
a piece of teflon string around them joined to the female joint with a little slack.

That will prevent the falling stopper hazard which is really dangerous. I had a real close call once and it scared the shit out of me contemplating what could have happened.

For glass stoppers that you really want to stay put use
#18 solid copper wire with 3 or 4 wraps.
View user's profile View All Posts By User
The_Davster
A pnictogen
*******




Posts: 2861
Registered: 18-11-2003
Member Is Offline

Mood: .

[*] posted on 8-7-2007 at 13:47


Cracked the lightbulb in the hood at work with one. I use ductape to secure them.



View user's profile View All Posts By User
DrP
National Hazard
****




Posts: 625
Registered: 28-9-2005
Member Is Offline

Mood: exothermic

[*] posted on 9-7-2007 at 01:23


What about the little plastic clips you get for quick fit joints. They get used to keep stoppers on I think. Good thing is that if there was a really big pressure increase, I think they would give, allowing the stopper to pop off or at least rise out of the joint a bit to release the pressure.
View user's profile View All Posts By User
YT2095
International Hazard
*****




Posts: 1091
Registered: 31-5-2003
Location: Just left of Europe and down a bit.
Member Is Offline

Mood: within Nominal Parameters

[*] posted on 9-7-2007 at 03:05


I`ve had it happen with a number 71 gas jar bung before when using my bubbler, you can plug the output and nothing happens for a while, then the pump starts to change it`s sound then WHUP the bung bounces a good 4 inches.
not in it`self particularly dangerous unless you`re bubbling Cl2 or the likes.




\"In a world full of wonders mankind has managed to invent boredom\" - Death
Twinkies don\'t have a shelf life. They have a half-life! -Caine (a friend of mine)
View user's profile View All Posts By User
tito-o-mac
Hazard to Others
***




Posts: 117
Registered: 30-6-2007
Member Is Offline

Mood: No Mood

[*] posted on 9-7-2007 at 05:51


How about the one which uses air pressure or suction to secure itself?
You could wear safety glasses or install a barrier of some sort.
View user's profile View All Posts By User
tito-o-mac
Hazard to Others
***




Posts: 117
Registered: 30-6-2007
Member Is Offline

Mood: No Mood

[*] posted on 9-7-2007 at 05:54


You also try this out just for fun: take a bicycle pump, stuff a cork or stopper at one end and begin pumping. Soon after you will realise it's getting harder and harder, until you come to a point where there is a short "whoosh" sound and the stopper propels about a good 3-5 metres
View user's profile View All Posts By User

  Go To Top