Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
sulphur trioxide and water
On reading it seems if I try and heat sodium bisulphate then I get sodium trioxide.
But if I bubble this into water it goes mad and forms a mist of sulfuric acid.
So..............
Is it possible to have a glass water bath with one of those gas things like a upside down flower pot and a gas jar half full of air on top. Bubble the
trioxide into the water under the gas jar and trap the mist?
If I bubble the gas slow enough would the sulfuric mist mix with the water in the gas jar?
I am looking for a easy way to make sulfuric acid without using hydrochloric etc.
Or old batter thats dead, weak sulphuric from that and bubble as per set up above?
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Do you mean sodium bisulfate or bisulfite? I haven't heard of the first one decomposing that way.
Firstly, I would suggest buying it if you can(unless you're just making it for chemistry's sake); you're likely to be using it for so many things
later on that you'll need more than you can likely make.
Secondly, sulfuric acid can indeed be using sulfur trioxide, but this is usually done in the industry by dissolving it in already concentrated
sulfuric acid to create oleum(fuming sulfuric acid), and then water is added to react with the sulfur trioxide in solution without any gas phases
getting in the way.
It can also be made by bubbling sulfur dioxide, readily made from bisulfite or metabisulfite into hydrogen peroxide, with a low yield.
Depending on how much research you've done, you might've known all that, but I thought I'd chip in.
|
|
|
Metacelsus
International Hazard
Posts: 2532
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
What's done in industry is absorbing the SO3 in concentrated sulfuric acid to make oleum, and then adding water to the oleum. Direct
reaction of SO3 with water is too violent.
Honestly, I'd just stop at the oleum, as it is harder to get than sulfuric acid.
Sorry, didn't notice No Tear's post.
[Edited on 10-10-2014 by Cheddite Cheese]
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Quote: Originally posted by Cheddite Cheese  | What's done in industry is absorbing the SO3 in concentrated sulfuric acid to make oleum, and then adding water to the oleum. Direct
reaction of SO3 with water is too violent.
Honestly, I'd just stop at the oleum, as it is harder to get than sulfuric acid.
[Edited on 10-10-2014 by Cheddite Cheese] |
Dude, trying to steal my spotlight?
|
|
|
AsocialSurvival
Harmless
Posts: 43
Registered: 8-10-2014
Member Is Offline
Mood: No Mood
|
|
Yes, you can make Sulfuric acid by vaporizing Sodium bisulfate and condensing it into water. There may be some mist, heat, and even splashing because
SO3 reacts exothermically with water. But, after some time everything will cool down and you're done.
Practically imagine all bi-salts as acid + that salt. Bisulfate is mixture of sulfate and sulfuric acid. You're just boiling or decomposing sulfuric
acid in this case.
Altough I prefer nuclear fusion, if you put extremely high heat and pressure on Oxygen, you will get Sulfur in unlimited quantities.
O + O => S
[Edited on 10-10-2014 by AsocialSurvival]
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
Hmm sounds like a lot of agro for little gain.
Back to messing with copper
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
Bisulfate decomposes to pyrosulfate and then SO3.
Bisulfite does not. Perhaps you have confused this with metabisulfite, which decomposes releasing SO2?
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
I have no idea now as i have totally confused myself! I will go check 
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
| Quote: Originally posted by Praxichys |
Bisulfate decomposes to pyrosulfate and then SO3.
Bisulfite does not. Perhaps you have confused this with metabisulfite, which decomposes releasing SO2?
|
I haven't worked with it before, so I can't tell for sure, but from Wikipedia: "sodium bisulfite releases sulfur dioxide gas when added to water or
products containing water." I didn't know if he meant heating it while anhydrous or while in water, as is often done with metabisulfite. I know he
said trioxide and not dioxide, but sulfur dioxide is more commonly used to produce sulfuric acid by amateur means as far as I've seen.
|
|
|
macckone
International Hazard
Posts: 2160
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Depending on the depth of the water and speed of gas generation, it is possible to dissolve sulfur trioxide in water.
However you should probably try sulphur dioxide using
the chamber method first. As the above procedure can
go badly in an explosive manner. Think sulfuric shower.
|
|
|
blargish
Hazard to Others
Posts: 166
Registered: 25-9-2013
Location: Canada
Member Is Offline
Mood: Mode Push
|
|
Yea, bubbling sulfur dioxide through an oxidizer is a MUCH easier method of obtaining sulfuric acid than trying to make it via SO3.
However, if you are trying to make SO3, another approach is to thermally decompose a persulfate salt with a little bit of concentrated
sulfuric acid as catalyst.
BLaRgISH
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
Its definitely the one you heat and get trioxide.
So if I do I need maximum containment, ok I need to think about this before trying. maybe gas jar of water upside down in tank of water then bell jar
over all of that.
Hmm drugs kicking in (prescribed)
|
|
|
Texium
Administrator
Posts: 4532
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
| Quote: Originally posted by AsocialSurvival | Altough I prefer nuclear fusion, if you put extremely high heat and pressure on Oxygen, you will get Sulfur in unlimited quantities.
O + O => S
|
Can you U2U me with some further info about this process? I am very intrigued.
|
|
|
macckone
International Hazard
Posts: 2160
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
You need one of these reaction vessels
en.Wikipedia.org/wiki/star
|
|
|
Jstuyfzand
Hazard to Others
Posts: 166
Registered: 16-1-2016
Location: Netherlands
Member Is Offline
Mood: Learning, Sorta.
|
|
Should be doable, got something to do for the weekend now.
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
On another note. The "little_ghost" persona has not posted in 6 months.
Perhaps this serial liar has finally left us in piece?
|
|
|
clearly_not_atara
International Hazard
Posts: 2715
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
SO2 IIRC has pretty good solubility in GAA; I wonder if that could be used as a way to increase the yield (using 30% H2O2 and SO2 at low temp):
http://www.orgsyn.org/demo.aspx?prep=CV7P0508
Not sure how easy it is to separate H2SO4 from HOAc though...
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
