Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Oily layer in HNO3 distilled from bisulphate and nitrate?
Junk_Enginerd
Hazard to Others
***




Posts: 251
Registered: 26-5-2019
Location: Sweden
Member Is Offline


[*] posted on 24-7-2020 at 07:50
Oily layer in HNO3 distilled from bisulphate and nitrate?


I've distilled a few hundred ml of red fuming nitric acid from sodium bisulphate and sodium nitrate. Went well and product seems good, except there's some form of immiscible oil in there as well. I'd estimate it to one or two percent of the total volume, floating around exactly like oil on water.

What might this oil be? Is it normal? The only contamination source I can imagine would be tape and hoses of silicone and pvc. Would that have contributed?
View user's profile View All Posts By User
Draeger
Hazard to Others
***




Posts: 185
Registered: 31-1-2020
Location: North-Rhine Westfalia, Germany
Member Is Offline

Mood: Slowly getting ready for new projects

[*] posted on 24-7-2020 at 08:19


I've heard HNO3 liquifies silicone rubber, so it might be that.



Collected elements:
Al, Cu, Ga, C (coal), S, Zn, Na

Collected compounds:

Inorganic:
NaOH; NaHCO3; MnCl2; MnCO3; CuSO4; FeSO4; aq. 30-33% HCl; aq. NaClO; aq. 9,5% ammonia; aq. 94-96% H2SO4; aq. 3% H2O2

Organic:
citric acid, sodium acetate, sodium citrate, petroleum, mineral oil
View user's profile View All Posts By User
Herr Haber
International Hazard
*****




Posts: 1236
Registered: 29-1-2016
Member Is Offline

Mood: No Mood

[*] posted on 24-7-2020 at 09:09


Have you seen any degradation in your tubing ?

Can you try to pipette it out ? You could redistill but the losses...
Anyway, be careful storing that RFNA if you leave whatever it is in there.

Edit: Degradation such as yellowing or stiffening.

[Edited on 24-7-2020 by Herr Haber]




The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
View user's profile View All Posts By User
Junk_Enginerd
Hazard to Others
***




Posts: 251
Registered: 26-5-2019
Location: Sweden
Member Is Offline


[*] posted on 24-7-2020 at 10:05



rquote=641315&tid=155856&author=Draeger]I've heard HNO3 liquifies silicone rubber, so it might be that.[/rquote]

Really? That's annoying. I knew silicone wasn't going to be resistant to nitric acid, but I didn't think it would do something like that.

Quote: Originally posted by Herr Haber  
Have you seen any degradation in your tubing ?

Can you try to pipette it out ? You could redistill but the losses...
Anyway, be careful storing that RFNA if you leave whatever it is in there.

Edit: Degradation such as yellowing or stiffening.

[Edited on 24-7-2020 by Herr Haber]


Haha, oh yeah. Those tubes are definitely single use. The smooth, transparent and supple silicone hose becomes an opaque and stiff mess after a while. That goes for the PVC parts as well.

Sure. It coalesces into a nice coherent floating puddle that I could probably catch quite easily. Just wasn't sure if I might have missed something and that it might have been normal.
View user's profile View All Posts By User
Herr Haber
International Hazard
*****




Posts: 1236
Registered: 29-1-2016
Member Is Offline

Mood: No Mood

[*] posted on 24-7-2020 at 11:38


Where do these tubes go in your distillation setup so they contaminate the product ?

I mean... I can see pvc on a vacuum pump inlet and silicone on the outlet. Both would get shredded in a single run but wouldnt contaminate your acid.

Viton is my favourite choice to connect to gas outlets, washing bottles and such. Sometimes silicone is still useful (and cheap), so is PVC. You'll appreciate not having to take special care removing rotting tubing and cleaning the connections of your glassware




The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
View user's profile View All Posts By User
outer_limits
Hazard to Others
***




Posts: 139
Registered: 3-3-2020
Member Is Offline

Mood: hybridized

[*] posted on 24-7-2020 at 12:17


If your entire apparatus was made of glass with ground glass joint I would say that it could be grease - if you used grease.
Using sulphuric acid is better idea because nitric acid is strong oxidizer and grease doesn't have a chance.

Tubing degradation products couldn't contaminate the product if they were used outside apparatus.
But you mentioned that you used a tape, it could be the source of contamination.

If I were you I would clean the product.

[Edited on 24-7-2020 by outer_limits]




View user's profile View All Posts By User
Syn the Sizer
National Hazard
****




Posts: 595
Registered: 12-11-2019
Location: Canada
Member Is Offline


[*] posted on 24-7-2020 at 13:17


Yes your best bet with distilling nitric acid is no thermometer unless you have a viton seal. Otherwise just stick a stopper in the top of the stillhead. Use sulfuric acid to seal the joints and if feeding gas to a secondary vessel to make dilute acid use a good resistant tubing, PTFE tubing works but is very rigid and due to its non-stick properties really doesn't want to stay on the gas outlet.

Nitric acid will eat everything. You should store it in a resistant bottle with a PTFE sealed lid or glass stoppered bottle.

I know a lab in the city that gets tons of stuff in PTFE bottles, different sizes, they transfer out of the bottles into their storage and chuck the bottles. One of the employees told me to ask if I could have some when the lab starts running again.
View user's profile View All Posts By User
Junk_Enginerd
Hazard to Others
***




Posts: 251
Registered: 26-5-2019
Location: Sweden
Member Is Offline


[*] posted on 26-7-2020 at 14:31


Quote: Originally posted by Herr Haber  
Where do these tubes go in your distillation setup so they contaminate the product ?

I mean... I can see pvc on a vacuum pump inlet and silicone on the outlet. Both would get shredded in a single run but wouldnt contaminate your acid.

Viton is my favourite choice to connect to gas outlets, washing bottles and such. Sometimes silicone is still useful (and cheap), so is PVC. You'll appreciate not having to take special care removing rotting tubing and cleaning the connections of your glassware


The tubes connect the reactor to the condenser, and as such will take the full force of boiling HNO3, hot NO2 and O2.

Quote: Originally posted by outer_limits  
If your entire apparatus was made of glass with ground glass joint I would say that it could be grease - if you used grease.
Using sulphuric acid is better idea because nitric acid is strong oxidizer and grease doesn't have a chance.

Tubing degradation products couldn't contaminate the product if they were used outside apparatus.
But you mentioned that you used a tape, it could be the source of contamination.

If I were you I would clean the product.

[Edited on 24-7-2020 by outer_limits]


No grease. Also no glass joints, silicone/pvc tubing with PTFE stoppers.

Indeed sulfuric acid is better, as is buying RFNA right off the shelf, but sodium bisulfate is the closest I'll get...

Quote: Originally posted by Syn the Sizer  
Yes your best bet with distilling nitric acid is no thermometer unless you have a viton seal. Otherwise just stick a stopper in the top of the stillhead. Use sulfuric acid to seal the joints and if feeding gas to a secondary vessel to make dilute acid use a good resistant tubing, PTFE tubing works but is very rigid and due to its non-stick properties really doesn't want to stay on the gas outlet.

Nitric acid will eat everything. You should store it in a resistant bottle with a PTFE sealed lid or glass stoppered bottle.

I know a lab in the city that gets tons of stuff in PTFE bottles, different sizes, they transfer out of the bottles into their storage and chuck the bottles. One of the employees told me to ask if I could have some when the lab starts running again.


I do have some PTFE tubing, but it is the kind used for 3d printers and as such the inner diameter is <2 mm, which ends up creating complicating pressure levels that are tough to seal. That's why I gave silicone and PVC tubing a go, aware that they would probably be single use.

It does indeed have a healthy appetite... It's sitting in a glass bottle.
View user's profile View All Posts By User
Syn the Sizer
National Hazard
****




Posts: 595
Registered: 12-11-2019
Location: Canada
Member Is Offline


[*] posted on 27-7-2020 at 05:57


Quote: Originally posted by Junk_Enginerd  

No grease. Also no glass joints, silicone/pvc tubing with PTFE stoppers.


I think this is where the oily layer is coming from, you need glass to distill HNO3


Quote: Originally posted by Junk_Enginerd  

Indeed sulfuric acid is better, as is buying RFNA right off the shelf, but sodium bisulfate is the closest I'll get...


Bisulfate works fine for the synthesis, it is cheap and easy to find. But to seal the glass joints sulfuric acid works best since it has a high boiling temp.

View user's profile View All Posts By User
Herr Haber
International Hazard
*****




Posts: 1236
Registered: 29-1-2016
Member Is Offline

Mood: No Mood

[*] posted on 27-7-2020 at 15:23


Reactor and tubing you say :cool:

I empty the reactor by applying pressure on one of the inlets. The silicone tubing doesnt like the leftover acid (excess silver then left around 80° c until bubbling disappears so days)

On the funnel is thick Viton. Around the flask and in the second picture is another thinner Viton tube that I leave connected to the glass.
I use it for NOx, chlorine, dipping in NaOH etc.
It doesnt show any sign of aging.

Teflon is too rigid for tubes unless you plan to install them semi permanently somewhere. But I love teflon. See all the white squares ? :P

IMG_3239.JPG - 90kBIMG_3240.JPG - 46kB




The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
View user's profile View All Posts By User
Syn the Sizer
National Hazard
****




Posts: 595
Registered: 12-11-2019
Location: Canada
Member Is Offline


[*] posted on 28-7-2020 at 07:49


I was curious if you could get viton tubing, I was googling and all I could really find was seals. I agree PTFE tubing is worse than copper for moldability. Copper once bent stays in position, even with heating PTFE doesn't really hold form. I was curious if they made PTFE springs. I feel with how rigid and form.holding PTFE is it could make a decent low force chemically resistant spring.

Is the tube reasonably priced?
View user's profile View All Posts By User
Herr Haber
International Hazard
*****




Posts: 1236
Registered: 29-1-2016
Member Is Offline

Mood: No Mood

[*] posted on 28-7-2020 at 13:36


10/12 mm is 26.10E per meter from one of my expensive sources.

It's about the same price as PTFE and looking back it's a very good investment.






The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
View user's profile View All Posts By User

  Go To Top