Keras
National Hazard
Posts: 864
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
What to do with a bottle of 60% HF?
So, there it is. I’ve ordered a bottle of 60% HF, because it was not that expensive, but I have no idea what to do with it except spill it on
limestome gravel to make CaF2.
Any suggestion? Fluorosulfonic acid? Mixing it with nitric acid doesn't seem to lead to new products, just a powerful etchant. Can I get
trifluoroacetic acid from HF and glacial acetic acid?
[Edited on 21-5-2019 by Keras]
|
|
Pumukli
National Hazard
Posts: 696
Registered: 2-3-2014
Location: EU
Member Is Offline
Mood: No Mood
|
|
This is not a toy, but of course you are well aware of it. :-) Don't spill it on anything living, if possible!
If you want to "waste" it on CaCO3 then do it, though avoid the escaping fine mist...
If I were you I'd convert it into something less toxic but still usable thing, say NaBF4. Dissolve it in borax-NaOH mixture, or something like that,
look up the relevant preparation in an inorganic lab manual.
|
|
WGTR
National Hazard
Posts: 971
Registered: 29-9-2013
Location: Online
Member Is Offline
Mood: Outline
|
|
Are you aware of the special hazards that this material possesses? Burns are not immediately obvious, and bind up the calcium in your body, the kind
that bones need for support, and nerves need to function. It’s a painful death. When I have used it I use two pairs of long gloves, have a
neutralizing solution and running water nearby, and have fresh tubes of calcium gluconate gel as an antidote. That’s just what gets applied to skin
while on the way to the hospital.
To answer your question, I’ve used it to etch glass slides to make micro channel reactors. That was cool.
|
|
woelen
Super Administrator
Posts: 8003
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Why do you order chemicals when you do not know what to do with it? Especially HF is really nasty. The 60% acid also is strongly fuming and for that
reason it is VERY hard to handle safely.
If I were you, I would dilute it to 40% or so, making it a non-fuming liquid, which is much easier and safer to handle. But still, with 40% acid you
have to be very careful. Getting it on your body will cause really serious health issues or even death.
One interesting thing might be to convert the acid to HBF4, using B2O3. Beware with the reaction, it is quite exothermic, slowly add B2O3 to the acid
in small portions. Try to use as precisely as possible the right stoichiometric amount of B2O3 and after the final addition, add 1% more of B2O3 to
assure that no free HF is present anymore. This slight excess of B2O3 will cause formation of a little mixed fluoro/hydroxo boric acids.
|
|
Keras
National Hazard
Posts: 864
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by WGTR | Are you aware of the special hazards that this material possesses? Burns are not immediately obvious, and bind up the calcium in your body, the kind
that bones need for support, and nerves need to function. It’s a painful death. When I have used it I use two pairs of long gloves, have a
neutralizing solution and running water nearby, and have fresh tubes of calcium gluconate gel as an antidote. That’s just what gets applied to skin
while on the way to the hospital.
|
Don't worry. I'm not a daredevil. I know pretty well where I'm going and have read extensive litterature on how to handle HF safely. Besides, I don't
intend to use more than a very few milliliters at once. And yeah, I have calcium gluconate available, and I'll dip the HF bottle in a cold water +
CaCl2 bath to take care of dripping.
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
I had a colleague who got some on his finger, tiniest little drop without noticing, then after work, it started to became a noticeable pain.
The next day they amputated his finger tip(luckily he only got it on the tip).
Be really careful with it!
|
|
Keras
National Hazard
Posts: 864
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by woelen | Why do you order chemicals when you do not know what to do with it? Especially HF is really nasty. The 60% acid also is strongly fuming and for that
reason it is VERY hard to handle safely. |
I agree. That sounds dumb. I did it because I’m not sure I'll be able to get it later if I need it for whatever purpose. I don't like stockpiling,
but in this case, given the way less and less reactants are available, I finally gave in. I pondered much before, though, as I'm perfectly aware of
the risks this product poses.
Quote: Originally posted by woelen |
If I were you, I would dilute it to 40% or so, making it a non-fuming liquid, which is much easier and safer to handle. But still, with 40% acid you
have to be very careful. Getting it on your body will cause really serious health issues or even death.
One interesting thing might be to convert the acid to HBF4, using B2O3. Beware with the reaction, it is quite exothermic, slowly add B2O3 to the acid
in small portions. Try to use as precisely as possible the right stoichiometric amount of B2O3 and after the final addition, add 1% more of B2O3 to
assure that no free HF is present anymore. This slight excess of B2O3 will cause formation of a little mixed fluoro/hydroxo boric acids.
|
I don't have B2O3, but I have boric acid and a heating mantle that goes to 400 °C, so I suppose I could make it by dehydrating
boric acid. Ever done that? EDIT: Apparently, HBF4 can be directly synthesised using boric acid, so the dehydration is not necessary.
Quote: Originally posted by karlos³ | I had a colleague who got some on his finger, tiniest little drop without noticing, then after work, it started to became a noticeable pain.
The next day they amputated his finger tip(luckily he only got it on the tip).
Be really careful with it! |
I have ordered full size, thick nitrile gloves, and I'll wear standard blue thin nitrile gloves underneath.
[Edited on 21-5-2019 by Keras]
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Dissolve a dead body.exactly how much HF does it take to dissolve someone. For example take 1kg of chicken carcass bones, blood,skin,meat etc and see
how many ml's of fuming HF acid it takes to make it into something that can be poured down the drain.before anyone winges and moans this is a
perfectly valid experiment.
|
|
Keras
National Hazard
Posts: 864
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by draculic acid69 | Dissolve a dead body.exactly how much HF does it take to dissolve someone. For example take 1kg of chicken carcass bones, blood,skin,meat etc and see
how many ml's of fuming HF acid it takes to make it into something that can be poured down the drain.before anyone winges and moans this is a
perfectly valid experiment. |
This has already been done and with HCl and sulphuric acid as comparison.
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
I'll be sure to check that out.thanks
|
|