RU_KLO
Hazard to Others
Posts: 147
Registered: 12-10-2022
Location: Argentina
Member Is Offline
|
|
Understanding (1+1) Reagent
In some books one can read a (1+1) H2SO4 solution.
From the AOAC:
"in expressions (1+2) (5+4), etc used in connection with name of a reagent, first numeral indicates volume reagent used, and second numeral indicates
volume of H2O. For example: HCl (1+2) means reagent prepared by mixing one volume of HCl + 2 Volumes of H2O."
From this:
Where does concentration (molarity) takes part? (I think is not the same (1+1) 36%HCl than (1+1) 20%HCl)
Also it speaks of volume, and not weight. (what I mean is v/v , w/w; w/v?)
for example: if 100% H2SO4 is 18.11M, then solultion 1+1 H2SO4 is 9.05 M?
Is there a basic formula which transforms (x+x) Reagent, to Molarity?
Go SAFE, because stupidity and bad Luck exist.
|
|
|
Texium
Administrator
Posts: 4516
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
What a confusing and unintuitive convention. There can't be a simple formula for translating to molarity because it would depend entirely on the
reagent being diluted. There is a good reason everyone uses molarity these days.
|
|
|
Bedlasky
International Hazard
Posts: 1219
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
Concentration of acid is usually most commonly available. So 36% HCl, 65% HNO3, 96% H2SO4 etc.
|
|
|
B(a)P
International Hazard
Posts: 1116
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Can you provide an example of a book/document that uses this convention?
By AOAC do you mean Association of Official Agricultural Chemists? Which document is the quoted text in your original post from?
It is not possible to come up with a formula until you understand if the '(1+1)' refers to volume, mass or something else.
|
|
|
Sulaiman
International Hazard
Posts: 3558
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
eg sulphuric acid (1+2)
Assume 18M acid, 1 Iitre=18 moles
Add to 2 litres of water to make 3 litres total containing 18 moles acid
18 moles in 3 litres = 6 moles/litre = 6M
I think that here may be very slightly less than 3 litres total when 1 litre of acid is added to 2 litres of water, but it
is not significant
(unless you are doing precsion titrations etc. but normally you would titrate the diluted acid in such a case)
Just from memory..... not certain.
I believe that when using dilute acid for general reactions,
precise concentration is not critical:
a little more concentrated and the reaction rate will increase
and less concentrated will be slower.
Don't concern yourself too much with precision in such cases.
Also, when you buy concentrated acid, the precise molarity is rarely known.
And if exposed to air, sulphuric acid slowly absorbs moisture, diluting itself,
. 37% HCl(aq) is more concentrated than the 20.2% azeotrope so it will loose HCl as a (highly corrosive to steel) gas., until the azeotrope
is reached.
. if you just look at 69% nitric acid too long it will slowly decompose the HNO3
etc.
........................
PS if you want a formula;
Let
M1 = starting molarity of concentrated liquid
M2 = final molarity of diluted liquid
Mixture = (a + b)
M2 = M1 x [a/(a + b)]
eg sulphuric acid 18M (1 + 2)
M2 = 18 x 1/(1 + 2) = 18/3 = 6
[Edited on 15-11-2023 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
woelen
Super Administrator
Posts: 7977
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
This "(a+b)" convention indeed is horrible.
What do they mean with "(1+1)" HCl? You say 1 volume of HCl with one volume of water. But what is one volume of HCl? Most concentrated acid you can
buy is 37% by weight. Most common concentration is 30...31%, at least where I live. Still quite concentrated, but not fuming as nastily as a 37%
solution. But 10% HCl also is quite common these days.
And also, mixing 1 volume of compound A with 1 volume of compound B may lead to a total volume, different from 2 volumes. The difference can be a few
percent.
This notation only is useful if the acid itself is well-defined, according to some written standard, otherwise it remains a matter of guessing and it
even depends on where you live.
|
|
|
RU_KLO
Hazard to Others
Posts: 147
Registered: 12-10-2022
Location: Argentina
Member Is Offline
|
|
Quote: Originally posted by B(a)P  | Can you provide an example of a book/document that uses this convention?
By AOAC do you mean Association of Official Agricultural Chemists? Which document is the quoted text in your original post from?
It is not possible to come up with a formula until you understand if the '(1+1)' refers to volume, mass or something else. |
"Officila Methods of Analysis" 15th ed, 1990. Associaton of Official Analytical Chemist"
As Bedlasky said, probably, as some Acid concentration are listed in a previous paragraph, these figures (1+1) reg, refers to them.
here is the page:
Go SAFE, because stupidity and bad Luck exist.
|
|
|
Bedlasky
International Hazard
Posts: 1219
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
| Quote: Originally posted by woelen | This "(a+b)" convention indeed is horrible.
What do they mean with "(1+1)" HCl? You say 1 volume of HCl with one volume of water. But what is one volume of HCl? Most concentrated acid you can
buy is 37% by weight. Most common concentration is 30...31%, at least where I live. Still quite concentrated, but not fuming as nastily as a 37%
solution. But 10% HCl also is quite common these days.
And also, mixing 1 volume of compound A with 1 volume of compound B may lead to a total volume, different from 2 volumes. The difference can be a few
percent.
This notation only is useful if the acid itself is well-defined, according to some written standard, otherwise it remains a matter of guessing and it
even depends on where you live. |
Sulaiman described it well. This is not something that is used for precise things. These A+B acids are usually used for acidification in titrations or
tests. There is no need for precise concentration. As I said, concentrated acids are used in labs mostly in these concentration: 35-37% HCl, 65-68%
HNO3, 96% H2SO4, 100% acetic acid, 24-26% NH3 etc. I don't find this convetion confusing at all.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
