nikotyna1939
Hazard to Self
Posts: 59
Registered: 26-9-2018
Location: reverse poland flag or nusantara
Member Is Offline
Mood: THINK 3R REDUCE REUSE RECYCLE
|
|
Dissolving Manganese Dioxide in Sulfuric Acid?
At what temprerature will Manganese Dioxide starting to dissolve in Sulfuric Acid to produce Manganese Sulfate?
Does Manganese Dioxide reacts with Sulfuric Acid at room temprerature?
|
|
|
RU_KLO
Hazard to Others
Posts: 147
Registered: 12-10-2022
Location: Argentina
Member Is Offline
|
|
I think not, because MnO2 is insoluble.
But boiling concentrated H2SO4 (VERY VERY DANGEROUS) could dissolve MnSO4.
like I said in another of your posts, the route is to transform MnO2 to Mn2O3 by blowtorch heat and then leach it with H2SO4. ( I use 30% conc. ie
battery acid concentration)
Check the permanganate post.
Go SAFE, because stupidity and bad Luck exist.
|
|
|
Sulaiman
International Hazard
Posts: 3561
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
In Wikipedia, manganese dioxide, reactions
Hot concentrated sulfuric acid reduces MnO2 to manganese(II) sulfate:
2 MnO2 + 2 H2SO4 → 2 MnSO4 + O2 + 2 H2O
......................................
So the evolution of oxygen should drive the reaction,
and, at a guess, if hot enough (boiling) the water would also be boiled off, increasing yield that may otherwise be decreased by atmospheric oxygen?
(as above - boiling conc. sulphuric acid is hazardous - it can 'bump' VIOLENTLY, so take extra care)
PS when the solution cools I would expect anhydrous manganese sulphate to precipitate out,
probably VERY hygroscopic.
Another guess 
[Edited on 14-3-2024 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
DraconicAcid
International Hazard
Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Add a reducing agent such as hydrogen peroxide (in dilute, not concentrated acid) if you want the reaction to go at reasonable temperatures.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
chornedsnorkack
National Hazard
Posts: 523
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
Remember that "concentrated sulphuric acid" actually spans a vast range of Hammett acidity values.
Quoting some numbers from a table by Ryabova et al. 1966:
3% +0,31
5% -0,02
18% -0,97
20% -1,10
30% -1,82
32% -1,96
35% -2,19
45% -2,95
47% -3,13
55% -3,91
57% -4,15
62% -4,82
65% -5,18
70% -5,92
72% -6,23
75% -6,72
77% -7,05
82% -7,84
85% -8,29
87% -8,60
90% -9,03
96% -9,88
98% -10,27
99% -10,57
99,6% -10,92
99,7% -11,01
99,95% -11,64
100.00% -11,94
So, not only the behaviour of 30% and 96% acid are different, but both are quite different from what happens at 70% or 100,00%.
[Edited on 15-3-2024 by chornedsnorkack]
|
|
|
Sulaiman
International Hazard
Posts: 3561
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
In a textbook/lab/home/classroom context
unless otherwise specified
"concentrated sulphuric acid"
means near azeotropic.
Anything else would need a concentration specification.
(molarity, w/w%, 'chamber' etc.)
[Edited on 15-3-2024 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
fx-991ex
Hazard to Self
Posts: 67
Registered: 20-5-2023
Member Is Offline
|
|
Am sorry to drift this off topic a little, but why the dioxide not react with sulfuric acid to make Mn(SO4)2?, i expect oxidizer to react with acid
usually.
[Edited on 15-3-2024 by fx-991ex]
|
|
|
solo
International Hazard
Posts: 3967
Registered: 9-12-2002
Location: Estados Unidos de La Republica Mexicana
Member Is Offline
Mood: ....getting old and drowning in a sea of knowledge
|
|
Quote: Originally posted by chornedsnorkack  | Remember that "concentrated sulphuric acid" actually spans a vast range of Hammett acidity values.
Quoting some numbers from a table by Ryabova et al. 1966:
3% +0,31
5% -0,02
18% -0,97
20% -1,10
30% -1,82
32% -1,96
35% -2,19
45% -2,95
47% -3,13
55% -3,91
57% -4,15
62% -4,82
65% -5,18
70% -5,92
72% -6,23
75% -6,72
77% -7,05
82% -7,84
85% -8,29
87% -8,60
90% -9,03
96% -9,88
98% -10,27
99% -10,57
99,6% -10,92
99,7% -11,01
99,95% -11,64
100.00% -11,94
So, not only the behaviour of 30% and 96% acid are different, but both are quite different from what happens at 70% or 100,00%.
[Edited on 15-3-2024 by chornedsnorkack] |
...is that the density of each concentration of the acid?
It's better to die on your feet, than live on your knees....Emiliano Zapata.
|
|
|
DraconicAcid
International Hazard
Posts: 4278
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
| Quote: Originally posted by solo | | Quote: Originally posted by chornedsnorkack | Remember that "concentrated sulphuric acid" actually spans a vast range of Hammett acidity values.
Quoting some numbers from a table by Ryabova et al. 1966:
3% +0,31
5% -0,02
18% -0,97
20% -1,10
30% -1,82
32% -1,96
35% -2,19
45% -2,95
47% -3,13
55% -3,91
57% -4,15
62% -4,82
65% -5,18
70% -5,92
72% -6,23
75% -6,72
77% -7,05
82% -7,84
85% -8,29
87% -8,60
90% -9,03
96% -9,88
98% -10,27
99% -10,57
99,6% -10,92
99,7% -11,01
99,95% -11,64
100.00% -11,94
So, not only the behaviour of 30% and 96% acid are different, but both are quite different from what happens at 70% or 100,00%.
[Edited on 15-3-2024 by chornedsnorkack] |
...is that the density of each concentration of the acid? |
The Hammett acidity function is essentially an extension of the pH scale into non-aqueous solvents.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
bnull
Hazard to Others
Posts: 150
Registered: 15-1-2024
Location: Between the Atlantic and the Pacific Ocean
Member Is Offline
Mood: Sleepy (again)
|
|
| Quote: Originally posted by fx-991ex | | Am sorry to drift this off topic a little, but why the dioxide not react with sulfuric acid to make Mn(SO4)2?, i expect oxidizer to react with
acid usually. |
Did you mean oxide? Mn4+ is not much stable. Its only compounds that I know are our subject (MnO2) and MnF4, which is
unstable and reacts with anything (air, water, solvents). Manganese likes to be 2+, that's why we need a reducing agent.
@solo: Those are the values in the Hammett acidity scale. It's like pH, for concentrated solutions. At low concentrations, the pH and Hammett values
are very close. (Nevermind.)
[Edited on 15-3-2024 by bnull]
Quod scripsi, scripsi.
B. N. Ull
P.S.: Did you know that we have a Library?
|
|
|
RU_KLO
Hazard to Others
Posts: 147
Registered: 12-10-2022
Location: Argentina
Member Is Offline
|
|
| Quote: Originally posted by fx-991ex | Am sorry to drift this off topic a little, but why the dioxide not react with sulfuric acid to make Mn(SO4)2?, i expect oxidizer to react with acid
usually.
[Edited on 15-3-2024 by fx-991ex] |
It could react, but you need boiling concentrated, or maybe digestion ( long time medium temperature acid)
I think its because solubility of MnO2 is insoluble.
" Manganese (IV) dioxide (MnO2) is a strong oxidizer and is insoluble in water, nitric acid, or cold sulfuric acid, and it may slowly dissolve in
aqueous HCl to give off Cl 2 gas."
Methods for converting manganese dioxide into water-soluble manganese salts
goggle patent. EP2930163A1
Go SAFE, because stupidity and bad Luck exist.
|
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
