AndrewOfWallachia
Harmless
Posts: 9
Registered: 4-12-2023
Location: Romania
Member Is Offline
Mood: YAHAHHA THE YPERITE BLISTERS!
|
|
Concentrating storebought 15% muriatic acid
Hi! I have some 15% Muriatic acid, I really need to concentrate it to 30%. Is that possible by just adding a Hygroscopic material like CaCl2 to it and
then boiling it to remove just HCl(g) and the bubbling that through more of the 15% HCl Solution? Or does it only work with higher concentrations of
Muriatic acid? Or is there a way to boil the 15% with a reflux condenser so that the steam that rises gets condensed back but the HCl(g) can be
bubbled through more Muriatic Acid?
Thanks in advance!
[Edited on 21-3-2024 by AndrewOfWallachia]
|
|
|
fx-991ex
Hazard to Self
Posts: 67
Registered: 20-5-2023
Member Is Offline
|
|
Make more HCl with NaCl and NaHSO4 and absorb it in the 15% HCl, carefull its highly hygroscopic.
|
|
|
woelen
Super Administrator
Posts: 7977
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
You can concentrate it a little more to appr. 20% by careful boiling. Initially, mainly water boils off. In this way you can get close to 20% without
too much loss. Much more will not be possible, because the azeotrope with water is 22% or so. A few percents below that azeotrope, you already lose so
much HCl, that it hardly separates anymore.
With your almost 20% HCl, you then could try the trick with anhydrous CaCl2 and boiling off a mix, which is richer in HCl than 20%.
|
|
|
AndrewOfWallachia
Harmless
Posts: 9
Registered: 4-12-2023
Location: Romania
Member Is Offline
Mood: YAHAHHA THE YPERITE BLISTERS!
|
|
Quote: Originally posted by woelen  | You can concentrate it a little more to appr. 20% by careful boiling. Initially, mainly water boils off. In this way you can get close to 20% without
too much loss. Much more will not be possible, because the azeotrope with water is 22% or so. A few percents below that azeotrope, you already lose so
much HCl, that it hardly separates anymore.
With your almost 20% HCl, you then could try the trick with anhydrous CaCl2 and boiling off a mix, which is richer in HCl than 20%.
|
Whoa, -ANHYDROUS- CaCl2? As in, perfectly anhydrous? Can I realistically dry it that much?
|
|
|
Precipitates
Harmless
Posts: 31
Registered: 4-12-2023
Location: SE Asia
Member Is Offline
|
|
Yes! Just heat it to 300°C or so... 
CaCl2 will loose the last water molecule at 260°C.
https://rushim.ru/books/spravochniki/handbook-of-inorganic-c...
|
|
|
B(a)P
International Hazard
Posts: 1116
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
You can easily get to the monohydrate by sticking some calcium chloride in the oven on a tray set to high for an hour or so, depending on volume. I
would have thought the monohydrate would be fine for this purpose. If you want to go to anhydrous it is relatively easily achieved in an old stainless
frying pan on a very high heat.
If you have the correct vessel, some have reported success using a microwave to dry calcium chloride.
|
|
|
woelen
Super Administrator
Posts: 7977
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Anhydrous CaCl2 can be obtained in hardware stores as drying agent for air drying purposes. You can buy it in bags of 2 kg or so. At least, where I
live, this is available at many places OTC. This stuff is good enough for the purpose I mentioned in my previous post. An indeed, if you can't buy
anhydrous material, you can make it by heating more or less hydrated material.
|
|
|
chornedsnorkack
National Hazard
Posts: 523
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
Pass the constant compositions by alternate freezing and heating?
Freezing phase diagram:
https://picryl.com/media/phase-diagram-hcl-h2o-s-l-e2e2c6?zo...
15 % HCl should freeze out water ice above -40 and be capable of concentrating until 22...23% eutectic that freezes at -75 degrees if it nucleates.
But at 22...23%, you´re past the azeotrope which is 20,2%, and can get more concentrated HCl by distilling your mother liquor.
|
|
|
clearly_not_atara
International Hazard
Posts: 2696
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
IIRC benzoic acid or TsOH monohydrate have pretty low solubility in acidic water, so you could add benzoic anhydride (by the catalytic thermal
dehydration) or anhydrous toluenesulfonic acid (Nicodem's Dean-Stark method) and then simply filter. There will probably be a small amount of
contamination, which may or may not be acceptable.
[Edited on 04-20-1969 by clearly_not_atara]
|
|
|
Sulaiman
International Hazard
Posts: 3558
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Is 30% actually required (eg vs double quantity of 15%)?
Store bought muriatic acid is likely to contain various impurities,
so I think that purification/distillation should be a part of your concentration procedure.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Heating HCl solution above the 20.2% azeotropic mixture will just drive off HCl gas. To concentrate to 30%, you need to dissolve additional HCl gas in
it. How you produce that is up to you. Sulfuric and NaCl is classic. Watch out for heat of dissolution and the very real suckback risk.
|
|
|
chornedsnorkack
National Hazard
Posts: 523
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by UC235 | | Heating HCl solution above the 20.2% azeotropic mixture will just drive off HCl gas. To concentrate to 30%, you need to dissolve additional HCl gas in
it. How you produce that is up to you. Sulfuric and NaCl is classic. |
Heating HCl solution above the 20.2% azeotropic mixture would be one obvious possibility? Heat one vessel of 20+% solution, direct the vapours into
the other vessel of the same, which you are cooling.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
