Camroc37
Hazard to Others
Posts: 101
Registered: 4-8-2015
Location: USA
Member Is Offline
Mood: Must...Nitrate...EVERYTHING!
|
|
Distillation Apparatus question
I bought a 3-way adapter to make nitric acid, but realized the plastic cap may dissolve. Not certain though since it is laboratory equipment. Any
help/thoughts are appreciated. I asked the seller and he didn't know. Or you could say he didn't HNO! Ha. Ha. Sorry...
|
|
|
greenlight
National Hazard
Posts: 705
Registered: 3-11-2014
Member Is Offline
Mood: Energetic
|
|
Definitely looks like chem resistant PTFE plastic that comes with other glassware but its hard to tell.
If it is PTFE plastic, it will hold up against the HNO3.
If it is cheaper no-name glass item you never know.
Can always go to the hardware store grab a roll of plumbers PTFE thread tape and wrap its threads as extra protection then just give it a go.
[Edited on 23-8-2015 by greenlight]
The only use for an atomic bomb is to keep somebody else from using one.
George Wald
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
C37, normally there would be a rubber o-ring with PTFE protectors top and bottom ─ what you seem to have is a poorly made rubber stopper seemingly
without provision for inserting the needed thermometer . . .
But as GL said, PTFE tape is a boon in dealing with oxyacids; on joints, too, it's a reasonable alternative to stop-cock grease!
|
|
|
greenlight
National Hazard
Posts: 705
Registered: 3-11-2014
Member Is Offline
Mood: Energetic
|
|
Damn, must be a chinese knock off.
Looks the same colour as the Schott duran plastic on their glassware.
The only use for an atomic bomb is to keep somebody else from using one.
George Wald
|
|
|
Sulaiman
International Hazard
Posts: 3569
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I don't have huge experience here but in my opinion;
as is,
the nitric fumes/vapour will only get to the inside of the glass and rubber washer,
a thermometer can be used by piercing the central thin part of the rubber,
in which case
the inside of the glass, part of the thermometer and a very small area of rubber will be exposed to the vapour.
should be no problem.
I see no point in using ptfe tape in this case.
the threaded areas are just to allow the mechanical compression of the seal,
they do not and are not meant to form a gas tight seal.
worst case; the rubber will swell a little and over much use decompose,
cut a new silicone rubber washer or replace with a rubber O-ring.
common butyl rubber will be ok, fluorinated rubber (e.g. viton.) better.
The old guys used huge rubber bungs etc.
the small area of rubber exposed in this case is negligible,
so go ahead and use as-is.
[Edited on 23-8-2015 by Sulaiman]
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Selection of chemically compatible materials of construction is crucial. The Cole-Parmer Chemical Compatibility Database is very useful for material
selection:
http://www.coleparmer.com/Chemical-Resistance
When dealing with hot concentrated nitric acid the correct selection of elastomer is important. I've had black rubber O-rings of unknown composition
completely destroyed when making con HNO3.
Black rubber O-rings are cheaply available at my local hardware store (as well as black rubber stoppers). But I don't know the rubber composition:
is it natural rubber, Viton, EPDM, or what? By buying from a supplier like McMaster-Carr I can specify the rubber composition.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Camroc37
Hazard to Others
Posts: 101
Registered: 4-8-2015
Location: USA
Member Is Offline
Mood: Must...Nitrate...EVERYTHING!
|
|
Quote: Originally posted by Magpie  | Selection of chemically compatible materials of construction is crucial. The Cole-Parmer Chemical Compatibility Database is very useful for material
selection:
http://www.coleparmer.com/Chemical-Resistance
When dealing with hot concentrated nitric acid the correct selection of elastomer is important. I've had black rubber O-rings of unknown composition
completely destroyed when making con HNO3.
Black rubber O-rings are cheaply available at my local hardware store (as well as black rubber stoppers). But I don't know the rubber composition:
is it natural rubber, Viton, EPDM, or what? By buying from a supplier like McMaster-Carr I can specify the rubber composition.
|
It is cheap china. (Didn't specify type) I will try using as-is, but in worst case scenario I can have PTFE at hand and ready to use.
[Edited on 23-8-2015 by Camroc37]
|
|
|
DFliyerz
Hazard to Others
Posts: 241
Registered: 22-12-2014
Member Is Offline
Mood: No Mood
|
|
A little late, but do not use this. I used this with nitric acid, and the thermometer fell in and broke inside my flask.
|
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Nitric acid destroys rubber. The only o-rings I know of that will mostly put up with HNO3 are viton. Best approach is to just use a stopper and figure
out the concentration later.
|
|
|
Sulaiman
International Hazard
Posts: 3569
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
| Quote: Originally posted by DFliyerz | | A little late, but do not use this. I used this with nitric acid, and the thermometer fell in and broke inside my flask. |
If you buy some cheap rubber O-rings that are a tight fit on your thermometer
put one on your thermometer a little above the plastic cap
even if the internal rubber corrodes or the plastic fails
the O-ring will prevent the thermometer crashing into the bottom of your flask.
Even a rubber band wrapped around the thermometer stem many times will work long enough to prevent disaster,
if you are attentive enough to notice the thermometer drop a little.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I just dropped a thermometer into a flask and broke the thermometer... it was tight when I assembled the apparatus, but thermal expansion loosened the
adapter... fortunately, the thermometer was a cheap one that came with a mostly decent lab kit that was the cheapest available... and it just so
happens that I bought an extra thermometer yesterday. Taking a look at the thermometer adapters I was using, they are junk too.. fortunately, I have
some high-quality ones that I ordered from a reputable Chinese supplier.
My expensive 350 degree mercury thermometer (also Chinese) has a high-density plastic ring permanently mounted at the top. Seems like a good idea....
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
